startTime=0
stopTime=3600
tolerance=1e-06
numberOfIntervals=2500
stepSize=1.44
wasm-jit simulation: simulate(Buildings.Fluid.DXSystems.Cooling.WaterSource.Examples.SingleSpeed,startTime=0,stopTime=3600,tolerance=1e-06,numberOfIntervals=2500,outputFormat="mat",variableFilter="time|sinSpeDX.eva.vol.T|sinSpeDX.sta_a1.T|sinSpeDX.sta_a2.T|sinSpeDX.sta_b2.T|sinSpeDX.sta_a1.X.1.|sinSpeDX.eva.vol.X_w|sinSpeDX.eva.dxCoi.mWat_flow|onOff.y|sinSpeDX.P|sinSpeDX.eva.dxCoi.Q_flow|sinSpeDX.watCooCon.Q_flow",fileNamePrefix="Buildings_latest_Buildings.Fluid.DXSystems.Cooling.WaterSource.Examples.SingleSpeed",simflags="-alarm=800  -emit_protected -lv LOG_STATS")
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings master/Fluid/DXSystems/Cooling/BaseClasses/Functions/warnIfPerformanceOutOfBounds.mo:18:3-24:36:writable]
|                 | |       | *** Warning: DX coil performance curves at nominal conditions are outside of bounds.
|                 | |       |              Capacity as a function of temperature  is outside of bounds 0.9 to 1.1.
|                 | |       |              The value of the curve fit is 1.2941
|                 | |       |              Check the coefficients of the function sta[1].perCur.capFunT.
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings master/Fluid/DXSystems/Cooling/BaseClasses/Evaporation.mo:194:3-203:27:writable]
|                 | |       | The following assertion has been violated during initialization at time 0.000000
|                 | |       | ((sinSpeDX.eva.watVapEva.nomVal.gamma <= sinSpeDX.eva.watVapEva.gammaMax)) --> "*** Warning: In DX coil model, gamma is too large for these coil conditions.
|                 | |       |     Instead of gamma = 1.5, a value of 0.393653, which
|                 | |       |     corresponds to a mass transfer effectiveness of 0.8, will be used.
|                 | |       |     Coil nominal performance data are:
|                 | |       |     nomVal.m_flow_nominal = 1.5
|                 | |       |     dX_nominal = XEvaOut_nominal-XEvaWetBulOut_nominal = 0.00969167 - 0.0102426 = -0.00055089
|                 | |       |     QLat_flow_nominal  = -4200
|                 | |       | "
LOG_SUCCESS       | info    | The initialization finished successfully with 3 homotopy steps.
LOG_STATS         | info    | ### STATISTICS ###
LOG_STATS         | info    | events
LOG_STATS         | info    | |       3 state events
LOG_STATS         | info    | |       0 time events
LOG_STATS         | info    | solver: dassl-events
LOG_STATS         | info    | |      87 steps taken
LOG_STATS         | info    | |      92 calls of functionODE
LOG_STATS         | info    | |      75 evaluations of jacobian
LOG_STATS         | info    | |       0 error test failures
LOG_STATS         | info    | |       0 convergence test failures
LOG_STATS         | info    | |       1 linear system solves
LOG_SUCCESS       | info    | The simulation finished successfully.