startTime=0
stopTime=86400
tolerance=1e-06
numberOfIntervals=2500
stepSize=34.56
wasm-jit simulation: simulate(Buildings.Fluid.DXSystems.Cooling.WaterSource.Validation.VariableSpeedEnergyPlus,startTime=0,stopTime=86400,tolerance=1e-06,numberOfIntervals=2500,outputFormat="mat",variableFilter="time|varSpeDX.eva.vol.T|TOutEPlu.y|varSpeDX.eva.m_flow|varSpeDX.eva.vol.Xi.1.|XEvaOutEPluMod.y|QCoo_flow.y|Q_flowEPlu.y|varSpeDX.P|PEPlu.y|TConOut.T|TCOutEPlu.y|varSpeDX.watCooCon.Q_flow|Q_flowConEPlu.y",fileNamePrefix="Buildings_12_Buildings.Fluid.DXSystems.Cooling.WaterSource.Validation.VariableSpeedEnergyPlus",simflags="-alarm=400  -emit_protected -lv LOG_STATS")
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.2-maint.12.x/Fluid/DXSystems/Cooling/BaseClasses/Evaporation.mo:185:3-194:27:writable]
|                 | |       | The following assertion has been violated during initialization at time 0.000000
|                 | |       | ((varSpeDX.eva.watVapEva.nomVal.gamma <= varSpeDX.eva.watVapEva.gammaMax)) --> "*** Warning: In DX coil model, gamma is too large for these coil conditions.
|                 | |       |     Instead of gamma = 1.5, a value of 0.346977, which
|                 | |       |     corresponds to a mass transfer effectiveness of 0.8, will be used.
|                 | |       |     Coil nominal performance data are:
|                 | |       |     nomVal.m_flow_nominal = 0.462462
|                 | |       |     dX_nominal = XEvaOut_nominal-XEvaWetBulOut_nominal = 0.00571197 - 0.00634552 = -0.000633544
|                 | |       |     QLat_flow_nominal  = -1689.5
|                 | |       | "
LOG_SUCCESS       | info    | The initialization finished successfully with 3 homotopy steps.
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.2-maint.12.x/Fluid/DXSystems/Cooling/BaseClasses/PartialCapacity.mo:121:7-134:38:writable]
|                 | |       | The following assertion has been violated at time 25200.000000
|                 | |       | ((not (varSpeDX.eva.dxCoi.TEvaIn > varSpeDX.eva.dxCoi.dryCoi.coiCap.sta[1].perCur.TEvaInMax or varSpeDX.eva.dxCoi.TEvaIn < varSpeDX.eva.dxCoi.dryCoi.coiCap.sta[1].perCur.TEvaInMin))) --> "*** Warning: Evaporator temperature TEvaIn is out of bounds in DX coil model at time = 25200.
|                 | |       |     stage     = 1
|                 | |       |     TEvaInMin = 283.15 Kelvin (10 degC)
|                 | |       |     TEvaIn    = 299.077 Kelvin (25.9269 degC)
|                 | |       |     TEvaInMax = 298.75 Kelvin (25.6 degC)
|                 | |       |     Extrapolation can introduce large errors.
|                 | |       |     This warning will only be reported once for each stage."
LOG_STATS         | info    | ### STATISTICS ###
LOG_STATS         | info    | events
LOG_STATS         | info    | |       0 state events
LOG_STATS         | info    | |      24 time events
LOG_STATS         | info    | solver: dassl-events
LOG_STATS         | info    | |    1370 steps taken
LOG_STATS         | info    | |    1589 calls of functionODE
LOG_STATS         | info    | |     975 evaluations of jacobian
LOG_STATS         | info    | |      13 error test failures
LOG_STATS         | info    | |       0 convergence test failures
LOG_STATS         | info    | |      10 linear system solves
LOG_SUCCESS       | info    | The simulation finished successfully.