startTime=0
stopTime=86400
tolerance=1e-06
numberOfIntervals=2500
stepSize=34.56
wasm-jit simulation: simulate(Buildings.Fluid.DXSystems.Cooling.AirSource.Validation.SingleSpeedPLR,startTime=0,stopTime=86400,tolerance=1e-06,numberOfIntervals=2500,outputFormat="mat",variableFilter="time|TOutDegC.Celsius|TOutEPlu.y|sinSpeDX.m_flow|XEvaOutMea.y|XEvaOutEPluMod.y|Q_flowMea.y|Q_flowEPlu.y|PMea.y|PEPlu.y",fileNamePrefix="Buildings_12_Buildings.Fluid.DXSystems.Cooling.AirSource.Validation.SingleSpeedPLR",simflags="-alarm=400  -emit_protected -lv LOG_STATS")
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.2-maint.12.x/Fluid/DXSystems/Cooling/BaseClasses/Evaporation.mo:185:3-194:27:writable]
|                 | |       | The following assertion has been violated during initialization at time 0.000000
|                 | |       | ((sinSpeDX.watVapEva.nomVal.gamma <= sinSpeDX.watVapEva.gammaMax)) --> "*** Warning: In DX coil model, gamma is too large for these coil conditions.
|                 | |       |     Instead of gamma = 1.5, a value of 0.347259, which
|                 | |       |     corresponds to a mass transfer effectiveness of 0.8, will be used.
|                 | |       |     Coil nominal performance data are:
|                 | |       |     nomVal.m_flow_nominal = 1.72
|                 | |       |     dX_nominal = XEvaOut_nominal-XEvaWetBulOut_nominal = 0.00562847 - 0.00620134 = -0.000572874
|                 | |       |     QLat_flow_nominal  = -5677.29
|                 | |       | "
LOG_SUCCESS       | info    | The initialization finished successfully with 3 homotopy steps.
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.2-maint.12.x/Fluid/DXSystems/Cooling/BaseClasses/PartialCapacity.mo:121:7-134:38:writable]
|                 | |       | The following assertion has been violated at time 25200.000000
|                 | |       | ((not (sinSpeDX.dxCoi.TEvaIn > sinSpeDX.dxCoi.dryCoi.coiCap.sta[1].perCur.TEvaInMax or sinSpeDX.dxCoi.TEvaIn < sinSpeDX.dxCoi.dryCoi.coiCap.sta[1].perCur.TEvaInMin))) --> "*** Warning: Evaporator temperature TEvaIn is out of bounds in DX coil model at time = 25200.
|                 | |       |     stage     = 1
|                 | |       |     TEvaInMin = 285.928 Kelvin (12.7778 degC)
|                 | |       |     TEvaIn    = 297.237 Kelvin (24.0865 degC)
|                 | |       |     TEvaInMax = 297.039 Kelvin (23.8889 degC)
|                 | |       |     Extrapolation can introduce large errors.
|                 | |       |     This warning will only be reported once for each stage."
LOG_STATS         | info    | ### STATISTICS ###
LOG_STATS         | info    | events
LOG_STATS         | info    | |      10 state events
LOG_STATS         | info    | |      25 time events
LOG_STATS         | info    | solver: dassl-events
LOG_STATS         | info    | |    2631 steps taken
LOG_STATS         | info    | |    3080 calls of functionODE
LOG_STATS         | info    | |    1185 evaluations of jacobian
LOG_STATS         | info    | |      29 error test failures
LOG_STATS         | info    | |       0 convergence test failures
LOG_STATS         | info    | |       1 linear system solves
LOG_SUCCESS       | info    | The simulation finished successfully.