startTime=0
stopTime=200
tolerance=1e-06
numberOfIntervals=2500
stepSize=0.08
wasm-jit simulation: simulate(Buildings.Fluid.Movers.Validation.PowerEuler,startTime=0,stopTime=200,tolerance=1e-06,numberOfIntervals=2500,outputFormat="mat",variableFilter="time|pump_y.P|pump_dp.P|pump_m_flow.P|pump_y.per.speed_nominal|y.y",fileNamePrefix="Buildings_11_Buildings.Fluid.Movers.Validation.PowerEuler",simflags="-alarm=400  -emit_protected -lv LOG_STATS")
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 11.1.2-maint.11.x/Fluid/Movers/BaseClasses/PartialFlowMachine.mo:389:3-396:39:writable]
|                 | |       | The following assertion has been violated during initialization at time 0.000000
|                 | |       | ((pump_dp.nominalValuesDefineDefaultPressureCurve)) --> "*** Warning in PowerEuler.pump_dp: Mover is flow or pressure controlled and uses default pressure curve.
|                 | |       | This leads to an approximate power consumption.
|                 | |       | Set nominalValuesDefineDefaultPressureCurve=true to suppress this warning."
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 11.1.2-maint.11.x/Fluid/Movers/BaseClasses/PartialFlowMachine.mo:417:3-427:39:writable]
|                 | |       | The following assertion has been violated during initialization at time 0.000000
|                 | |       | ((false)) --> "*** Warning in PowerEuler.pump_dp: Mover has per.etaHydMet=.Power_VolumeFlowRate or per.etaHydMet=.EulerNumber.
|                 | |       | This requires per.pressure to be provided.
|                 | |       | Because it is not, the model overrides this setting by using per.etaHydMet=.NotProvided.
|                 | |       | Also consider using models under Movers.Preconfigured which autopopulate a pressure curve."
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 11.1.2-maint.11.x/Fluid/Movers/BaseClasses/PartialFlowMachine.mo:389:3-396:39:writable]
|                 | |       | The following assertion has been violated during initialization at time 0.000000
|                 | |       | ((pump_m_flow.nominalValuesDefineDefaultPressureCurve)) --> "*** Warning in PowerEuler.pump_m_flow: Mover is flow or pressure controlled and uses default pressure curve.
|                 | |       | This leads to an approximate power consumption.
|                 | |       | Set nominalValuesDefineDefaultPressureCurve=true to suppress this warning."
LOG_SUCCESS       | info    | The initialization finished successfully with 3 homotopy steps.
LOG_STATS         | info    | ### STATISTICS ###
LOG_STATS         | info    | events
LOG_STATS         | info    | |       2 state events
LOG_STATS         | info    | |       0 time events
LOG_STATS         | info    | solver: dassl-events
LOG_STATS         | info    | |      69 steps taken
LOG_STATS         | info    | |      86 calls of functionODE
LOG_STATS         | info    | |      54 evaluations of jacobian
LOG_STATS         | info    | |       0 error test failures
LOG_STATS         | info    | |       0 convergence test failures
LOG_STATS         | info    | |       1 linear system solves
LOG_SUCCESS       | info    | The simulation finished successfully.