startTime=0
stopTime=3600
tolerance=1e-06
numberOfIntervals=2500
stepSize=1.44
wasm-jit simulation: simulate(Buildings.Fluid.DXSystems.Cooling.WaterSource.Examples.MultiStage,startTime=0,stopTime=3600,tolerance=1e-06,numberOfIntervals=2500,outputFormat="mat",variableFilter="time|mulSpeDX.eva.vol.T|mulSpeDX.sta_a1.T|mulSpeDX.sta_a2.T|mulSpeDX.sta_b2.T|mulSpeDX.sta_a1.X.1.|mulSpeDX.eva.vol.X_w|mulSpeDX.eva.dxCoi.mWat_flow|mulSpeDX.stage|mulSpeDX.P|mulSpeDX.eva.dxCoi.Q_flow|mulSpeDX.watCooCon.Q_flow",fileNamePrefix="Buildings_11_Buildings.Fluid.DXSystems.Cooling.WaterSource.Examples.MultiStage",simflags="-alarm=400  -emit_protected -lv LOG_STATS")
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 11.1.2-maint.11.x/Fluid/DXSystems/Cooling/BaseClasses/Functions/warnIfPerformanceOutOfBounds.mo:18:3-24:36:writable]
|                 | |       | *** Warning: DX coil performance curves at nominal conditions are outside of bounds.
|                 | |       |              Capacity as a function of temperature  is outside of bounds 0.9 to 1.1.
|                 | |       |              The value of the curve fit is 1.2941
|                 | |       |              Check the coefficients of the function sta[1].perCur.capFunT.
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 11.1.2-maint.11.x/Fluid/DXSystems/Cooling/BaseClasses/Evaporation.mo:185:3-194:27:writable]
|                 | |       | The following assertion has been violated during initialization at time 0.000000
|                 | |       | ((mulSpeDX.eva.watVapEva.nomVal.gamma <= mulSpeDX.eva.watVapEva.gammaMax)) --> "*** Warning: In DX coil model, gamma is too large for these coil conditions.
|                 | |       |     Instead of gamma = 1.5, a value of 0.0723694, which
|                 | |       |     corresponds to a mass transfer effectiveness of 0.8, will be used.
|                 | |       |     Coil nominal performance data are:
|                 | |       |     nomVal.m_flow_nominal = 1.8
|                 | |       |     dX_nominal = XEvaOut_nominal-XEvaWetBulOut_nominal = 0.00947842 - 0.00959899 = -0.000120567
|                 | |       |     QLat_flow_nominal  = -6000
|                 | |       | "
LOG_SUCCESS       | info    | The initialization finished successfully with 3 homotopy steps.
LOG_STATS         | info    | ### STATISTICS ###
LOG_STATS         | info    | events
LOG_STATS         | info    | |       5 state events
LOG_STATS         | info    | |       0 time events
LOG_STATS         | info    | solver: dassl-events
LOG_STATS         | info    | |     124 steps taken
LOG_STATS         | info    | |     132 calls of functionODE
LOG_STATS         | info    | |     109 evaluations of jacobian
LOG_STATS         | info    | |       0 error test failures
LOG_STATS         | info    | |       0 convergence test failures
LOG_STATS         | info    | |       4 linear system solves
LOG_SUCCESS       | info    | The simulation finished successfully.