startTime=1.58112e+07
stopTime=1.6416e+07
tolerance=1e-06
numberOfIntervals=5213
stepSize=116.018
wasm-jit simulation: simulate(Buildings.Fluid.DXSystems.Cooling.AirSource.Examples.SpaceCooling,startTime=1.58112e+07,stopTime=1.6416e+07,tolerance=1e-06,numberOfIntervals=5213,outputFormat="mat",variableFilter="time|rooSinSpe.vol.T|rooMulSpe.vol.T|rooVarSpe.vol.T|weaDat.weaBus.TDryBul|rooSinSpe.vol.Xi.1.|rooMulSpe.vol.Xi.1.|rooVarSpe.vol.Xi.1.|sinSpePow.y|varSpePow.y|mulSpePow.y",fileNamePrefix="Buildings_11_Buildings.Fluid.DXSystems.Cooling.AirSource.Examples.SpaceCooling",simflags="-alarm=400  -emit_protected -lv LOG_STATS")
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 11.1.2-maint.11.x/Fluid/Movers/BaseClasses/PartialFlowMachine.mo:389:3-396:39:writable]
|                 | |       | The following assertion has been violated during initialization at time 15811200.000000
|                 | |       | ((fan.nominalValuesDefineDefaultPressureCurve)) --> "*** Warning in SpaceCooling.fan: Mover is flow or pressure controlled and uses default pressure curve.
|                 | |       | This leads to an approximate power consumption.
|                 | |       | Set nominalValuesDefineDefaultPressureCurve=true to suppress this warning."
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 11.1.2-maint.11.x/Fluid/Movers/BaseClasses/PartialFlowMachine.mo:389:3-396:39:writable]
|                 | |       | The following assertion has been violated during initialization at time 15811200.000000
|                 | |       | ((fan1.nominalValuesDefineDefaultPressureCurve)) --> "*** Warning in SpaceCooling.fan1: Mover is flow or pressure controlled and uses default pressure curve.
|                 | |       | This leads to an approximate power consumption.
|                 | |       | Set nominalValuesDefineDefaultPressureCurve=true to suppress this warning."
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 11.1.2-maint.11.x/Fluid/Movers/BaseClasses/PartialFlowMachine.mo:389:3-396:39:writable]
|                 | |       | The following assertion has been violated during initialization at time 15811200.000000
|                 | |       | ((fan2.nominalValuesDefineDefaultPressureCurve)) --> "*** Warning in SpaceCooling.fan2: Mover is flow or pressure controlled and uses default pressure curve.
|                 | |       | This leads to an approximate power consumption.
|                 | |       | Set nominalValuesDefineDefaultPressureCurve=true to suppress this warning."
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 11.1.2-maint.11.x/Fluid/DXSystems/Cooling/BaseClasses/Evaporation.mo:185:3-194:27:writable]
|                 | |       | The following assertion has been violated during initialization at time 15811200.000000
|                 | |       | ((varSpeDX.watVapEva.nomVal.gamma <= varSpeDX.watVapEva.gammaMax)) --> "*** Warning: In DX coil model, gamma is too large for these coil conditions.
|                 | |       |     Instead of gamma = 1.5, a value of 0.52681, which
|                 | |       |     corresponds to a mass transfer effectiveness of 0.8, will be used.
|                 | |       |     Coil nominal performance data are:
|                 | |       |     nomVal.m_flow_nominal = 0.646123
|                 | |       |     dX_nominal = XEvaOut_nominal-XEvaWetBulOut_nominal = 0.00528111 - 0.00637893 = -0.00109782
|                 | |       |     QLat_flow_nominal  = -2694
|                 | |       | "
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 11.1.2-maint.11.x/Fluid/DXSystems/Cooling/BaseClasses/Evaporation.mo:185:3-194:27:writable]
|                 | |       | The following assertion has been violated during initialization at time 15811200.000000
|                 | |       | ((mulStaDX.watVapEva.nomVal.gamma <= mulStaDX.watVapEva.gammaMax)) --> "*** Warning: In DX coil model, gamma is too large for these coil conditions.
|                 | |       |     Instead of gamma = 1.5, a value of 0.52681, which
|                 | |       |     corresponds to a mass transfer effectiveness of 0.8, will be used.
|                 | |       |     Coil nominal performance data are:
|                 | |       |     nomVal.m_flow_nominal = 0.646123
|                 | |       |     dX_nominal = XEvaOut_nominal-XEvaWetBulOut_nominal = 0.00528111 - 0.00637893 = -0.00109782
|                 | |       |     QLat_flow_nominal  = -2694
|                 | |       | "
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 11.1.2-maint.11.x/Fluid/DXSystems/Cooling/BaseClasses/Evaporation.mo:185:3-194:27:writable]
|                 | |       | The following assertion has been violated during initialization at time 15811200.000000
|                 | |       | ((sinSpeDX.watVapEva.nomVal.gamma <= sinSpeDX.watVapEva.gammaMax)) --> "*** Warning: In DX coil model, gamma is too large for these coil conditions.
|                 | |       |     Instead of gamma = 1.5, a value of 0.52681, which
|                 | |       |     corresponds to a mass transfer effectiveness of 0.8, will be used.
|                 | |       |     Coil nominal performance data are:
|                 | |       |     nomVal.m_flow_nominal = 0.646123
|                 | |       |     dX_nominal = XEvaOut_nominal-XEvaWetBulOut_nominal = 0.00528111 - 0.00637893 = -0.00109782
|                 | |       |     QLat_flow_nominal  = -2694
|                 | |       | "
LOG_SUCCESS       | info    | The initialization finished successfully with 3 homotopy steps.
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 11.1.2-maint.11.x/Fluid/DXSystems/Cooling/BaseClasses/PartialCapacity.mo:121:7-134:38:writable]
|                 | |       | The following assertion has been violated at time 15849076.749054
|                 | |       | ((not (sinSpeDX.dxCoi.TEvaIn > sinSpeDX.dxCoi.dryCoi.coiCap.sta[1].perCur.TEvaInMax or sinSpeDX.dxCoi.TEvaIn < sinSpeDX.dxCoi.dryCoi.coiCap.sta[1].perCur.TEvaInMin))) --> "*** Warning: Evaporator temperature TEvaIn is out of bounds in DX coil model at time = 1.58491e+07.
|                 | |       |     stage     = 1
|                 | |       |     TEvaInMin = 285.928 Kelvin (12.7778 degC)
|                 | |       |     TEvaIn    = 297.06 Kelvin (23.9098 degC)
|                 | |       |     TEvaInMax = 297.039 Kelvin (23.8889 degC)
|                 | |       |     Extrapolation can introduce large errors.
|                 | |       |     This warning will only be reported once for each stage."
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 11.1.2-maint.11.x/Fluid/DXSystems/Cooling/BaseClasses/Evaporation.mo:59:3-62:61:writable]
|                 | |       | The following assertion has been violated at time 15900765.624401
|                 | |       | ((mulStaDX.watVapEva.m >= 0.0)) --> "Variable violating min constraint: 0.0 <= mulStaDX.watVapEva.m, has value: -2.68763e-07"
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 11.1.2-maint.11.x/Fluid/DXSystems/Cooling/BaseClasses/Evaporation.mo:59:3-62:61:writable]
|                 | |       | The following assertion has been violated at time 15907958.718588
|                 | |       | ((sinSpeDX.watVapEva.m >= 0.0)) --> "Variable violating min constraint: 0.0 <= sinSpeDX.watVapEva.m, has value: -4.41933e-18"
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 11.1.2-maint.11.x/Fluid/DXSystems/Cooling/BaseClasses/Evaporation.mo:59:3-62:61:writable]
|                 | |       | The following assertion has been violated at time 16404978.323422
|                 | |       | ((varSpeDX.watVapEva.m >= 0.0)) --> "Variable violating min constraint: 0.0 <= varSpeDX.watVapEva.m, has value: -7.68738e-12"
LOG_STATS         | info    | ### STATISTICS ###
LOG_STATS         | info    | events
LOG_STATS         | info    | |    2356 state events
LOG_STATS         | info    | |       0 time events
LOG_STATS         | info    | solver: dassl-events
LOG_STATS         | info    | |   125817 steps taken
LOG_STATS         | info    | |   162613 calls of functionODE
LOG_STATS         | info    | |   33867 evaluations of jacobian
LOG_STATS         | info    | |    3130 error test failures
LOG_STATS         | info    | |       0 convergence test failures
LOG_STATS         | info    | |   1988885 linear system solves
LOG_SUCCESS       | info    | The simulation finished successfully.