startTime=0
stopTime=200
tolerance=1e-06
numberOfIntervals=1000
stepSize=0.2
wasm artifact (cs: FMI 3.0 Co-Simulation, the artifact integrating itself with DASKR): simulate(ThermofluidStream.Examples.ReverseHeatPump,startTime=0,stopTime=200,tolerance=1e-06,numberOfIntervals=1000,outputFormat="mat",variableFilter="PI1.x|PI2.x|PI_Valve.x|TEVcooling.rear.m_flow|Time|accumulator.M|accumulator.U_med|accumulator.m_flow_in|boundaryFore1.rear.m_flow|boundaryRear.fore.m_flow|compressor.m_flow|discretizedHEX.thermalElementA.1..h|discretizedHEX.thermalElementA.2..h|discretizedHEX.thermalElementA.3..h|discretizedHEX.thermalElementA.4..h|discretizedHEX.thermalElementA.5..h|discretizedHEX.thermalElementB.1..h|discretizedHEX.thermalElementB.2..h|discretizedHEX.thermalElementB.3..h|discretizedHEX.thermalElementB.4..h|discretizedHEX.thermalElementB.5..h|discretizedHEX1.thermalElementA.1..h|discretizedHEX1.thermalElementA.2..h|discretizedHEX1.thermalElementA.3..h|discretizedHEX1.thermalElementA.4..h|discretizedHEX1.thermalElementA.5..h|discretizedHEX1.thermalElementB.1..h|discretizedHEX1.thermalElementB.2..h|discretizedHEX1.thermalElementB.3..h|discretizedHEX1.thermalElementB.4..h|discretizedHEX1.thermalElementB.5..h|firstOrder.y|receiver.M|receiver.U_med|twoPhaseSensorSelect.value|twoPhaseSensorSelect1.value|valveCompressorInletHeating.inlet.m_flow",fileNamePrefix="ThermofluidStream_dev_ThermofluidStream.Examples.ReverseHeatPump",simflags=" -alarm=390  -emit_protected -lv LOG_STATS -startTime=0 -stopTime=200 -tolerance=1e-06 -stepSize=0.2 -r=ThermofluidStream_dev_ThermofluidStream.Examples.ReverseHeatPump_cs_res.mat -s fmi3:cs",resimulateExecutable="ThermofluidStream_dev_ThermofluidStream_Examples_ReverseHeatPump.fmu")
Simulation execution failed for model: ThermofluidStream.Examples.ReverseHeatPump
LOG_STDOUT        | info    | wasm artifact loaded in 0.5 ms (model kernel linked against the cached adapter, 2.0 MB)
LOG_STDOUT        | warning | While solving non-linear system an assertion failed at time 12.2146.
|                 | |       | | The non-linear solver tries to solve the problem that could take some time.
|                 | |       | | It could help to provide better start-values for the iteration variables.
|                 | |       | | For more information simulate with -lv LOG_NLS_V
LOG_STDOUT        | warning | The default linear solver fails, the fallback solver with total pivoting is started at time 12.214616. That might raise performance issues, for more information use -lv LOG_LS.
LOG_STDOUT        | info    | Too many warnings, reached display limit of 3. Suppressing further warning messages of the same type.
LOG_STDOUT        | info    | Change limit with simulation flag -lvMaxWarn=<newLimit>
LOG_STDOUT        | warning | IRES equal to -2 was encountered and control is being returned to the calling program.
LOG_STDOUT        | warning | can't continue. time = 11.885521
ThermofluidStream.Examples.ReverseHeatPump: logStatusError: assertion failed
LOG_ERROR         | error   | fmi3DoStep returned error