(cd run_OMSimulator-cs-euler && /home/hudson/saved_omc/OMSimulator/install/bin/OMSimulator --resultFile=../ThermofluidStream_dev_ThermofluidStream.Idealized.Tests.Processes.Isobaric.Warnings3_OMSimulator-cs-euler_res.mat --stripRoot --tempDir=temp_ThermofluidStream_dev_ThermofluidStream_Idealized_Tests_Processes_Isobaric_Warnings3_OMSimulator-cs-euler_fmu --startTime=0 --stopTime=1 --stepSize=0.01 --mode=cs --timeout=240 --tolerance=1e-06 ../ThermofluidStream_dev_ThermofluidStream_Idealized_Tests_Processes_Isobaric_Warnings3_OMSimulator-cs-euler.fmu) info: *** FMU Simulation Info *** - model : ThermofluidStream.Idealized.Tests.Processes.Isobaric.Warnings3 (co-simulation) - fmiVersion: 2.0 - startTime : 0.000000 - stopTime : 1.000000 - tolerance : 1e-06 - stepSize : 0.01 info: Result file: ../ThermofluidStream_dev_ThermofluidStream.Idealized.Tests.Processes.Isobaric.Warnings3_OMSimulator-cs-euler_res.mat (bufferSize=10) info: Variable Warnings3.isobaricCycle.instanceName will not be stored in the result file, because the signal type is not supported info: Variable Warnings3.isobaricFlow.instanceName will not be stored in the result file, because the signal type is not supported info: Variable Warnings3.sink.instanceName will not be stored in the result file, because the signal type is not supported info: Variable Warnings3.sink1.instanceName will not be stored in the result file, because the signal type is not supported info: Variable Warnings3.source.displayPos1 will not be stored in the result file, because the signal type is not supported info: Variable Warnings3.source.displayPos2 will not be stored in the result file, because the signal type is not supported info: Variable Warnings3.source.displayPos3 will not be stored in the result file, because the signal type is not supported info: Variable Warnings3.source.displayPos4 will not be stored in the result file, because the signal type is not supported info: Variable Warnings3.source.instanceName will not be stored in the result file, because the signal type is not supported info: Variable Warnings3.source1.displayPos1 will not be stored in the result file, because the signal type is not supported info: Variable Warnings3.source1.displayPos2 will not be stored in the result file, because the signal type is not supported info: Variable Warnings3.source1.displayPos3 will not be stored in the result file, because the signal type is not supported info: Variable Warnings3.source1.displayPos4 will not be stored in the result file, because the signal type is not supported info: Variable Warnings3.source1.instanceName will not be stored in the result file, because the signal type is not supported LOG_ASSERT | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/ThermofluidStream 1.4.1-main/Idealized/Processes/Isobaric.mo:157:5-157:276:writable] | | | | The following assertion has been violated at time 0.270000 | | | | ((noEvent(abs(isobaricFlow.Q_flow) < 2.220446049250313e-16) or noEvent(abs(isobaricCycle.inlet.m_flow) > 2.220446049250313e-16))) --> "The heat flow rate in Warnings3.isobaricFlow is non zero, but the mass flow rate is zero, implying that the specific heat flow q := Q_flow/m_flow is infinite. | | | | The result is regularized." LOG_ASSERT | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/ThermofluidStream 1.4.1-main/Idealized/Processes/Isobaric.mo:157:5-157:276:writable] | | | | The following assertion has been violated at time 0.270000 | | | | ((noEvent(abs(isobaricFlow.Q_flow) < 2.220446049250313e-16) or noEvent(abs(isobaricCycle.inlet.m_flow) > 2.220446049250313e-16))) --> "The heat flow rate in Warnings3.isobaricCycle is non zero, but the mass flow rate is zero, implying that the specific heat flow q := Q_flow/m_flow is infinite. | | | | The result is regularized."