/home/hudson/saved_omc/OMSimulator/install/bin/OMSimulator  --tempDir=temp_IDEAS_IDEAS_Fluid_Actuators_Valves_Simplified_Examples_ThreeWayValveMotor_fmu --startTime=0 --stopTime=100 --stepSize=0.04 --timeout=50 --tolerance=1e-06 IDEAS_IDEAS_Fluid_Actuators_Valves_Simplified_Examples_ThreeWayValveMotor.fmu
warning: Failed to load settings: [json.exception.parse_error.101] parse error at line 4, column 1: syntax error while parsing value - unexpected '}'; expected end of input
warning: Failed to save settings: [json.exception.parse_error.101] parse error at line 4, column 1: syntax error while parsing value - unexpected '}'; expected end of input
info:    Set temp directory to    "/var/lib/jenkins1/ws/OpenModelicaLibraryTestingWork_2/OpenModelicaLibraryTesting/IDEAS_IDEAS.Fluid.Actuators.Valves.Simplified.Examples.ThreeWayValveMotor"
info:    Set working directory to "/var/lib/jenkins1/ws/OpenModelicaLibraryTestingWork_2/OpenModelicaLibraryTesting/IDEAS_IDEAS.Fluid.Actuators.Valves.Simplified.Examples.ThreeWayValveMotor"
info:    New model "model" with corresponding temp directory "/var/lib/jenkins1/ws/OpenModelicaLibraryTestingWork_2/OpenModelicaLibraryTesting/IDEAS_IDEAS.Fluid.Actuators.Valves.Simplified.Examples.ThreeWayValveMotor/model-uzcw1mr8"
info:    *** FMU Simulation Info ***
          - model:     model (model exchange)
          - path:      IDEAS_IDEAS_Fluid_Actuators_Valves_Simplified_Examples_ThreeWayValveMotor.fmu
          - startTime: 0.000000
          - stopTime:  100.000000
          - tolerance: 0.000001
          - stepSize:  0.040000
info:    model doesn't contain any continuous state
LOG_STDOUT        | info    | 
|                 | |       | Warning:
|                 | |       | ========
|                 | |       | It is recommended that the volume flow rate versus pressure relation
|                 | |       | of the fan or pump satisfies the minimum decrease condition
|                 | |       | 
|                 | |       |         (per.pressure.dp[i+1]-per.pressure.dp[i])
|                 | |       | d[i] = ------------------------------------------------- < -0
|                 | |       |        (per.pressure.V_flow[i+1]-per.pressure.V_flow[i])
|                 | |       | 
|                 | |       |  is
|                 | |       |   d[1]=0     
|                 | |       | 
|                 | |       | Otherwise, a solution to the equations may not exist if the fan or pump speed is reduced.
|                 | |       | In this situation, the solver will fail due to non-convergence and
|                 | |       | the simulation stops.
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/IDEAS 3.0.0/Fluid/Movers/BaseClasses/PartialFlowMachine.mo:348:3-357:39:writable]
|                 | |       | The following assertion has been violated during initialization at time 0.000000
|                 | |       | ((pumpFlow1.nominalValuesDefineDefaultPressureCurve)) --> "*** Warning: You are using a flow or pressure controlled mover with the
|                 | |       |              default pressure curve.
|                 | |       |              This leads to approximate calculations of the electrical power
|                 | |       |              consumption. Add the correct pressure curve in the record per
|                 | |       |              to obtain an accurate computation.
|                 | |       |              Setting nominalValuesDefineDefaultPressureCurve=true will suppress this warning."
info:    maximum step size for 'model.root': 0.040000
info:    Result file: model_res.mat (bufferSize=10)
info:    Final Statistics for 'model.root':
         NumSteps = 2500 NumRhsEvals  = 2501 NumLinSolvSetups = 125
         NumNonlinSolvIters = 2500 NumNonlinSolvConvFails = 0 NumErrTestFails = 0
info:    2 warnings
info:    0 errors