Environment - simulationEnvironment:
startTime=0
stopTime=1
tolerance=1e-06
numberOfIntervals=500
stepSize=0.002
Regular simulation: ./PowerGrids_dev_PowerGrids.Examples.IEEE14bus.IEEE14busStaticNetwork  -abortSlowSimulation -alarm=50  -emit_protected -lv LOG_STATS
stdout            | info    | Using sparse solver kinsol for nonlinear system 20 (1947),
|                 | |       | because density of 0.09 remains under threshold of 0.10.
stdout            | info    | Using sparse solver kinsol for nonlinear system 21 (2537),
|                 | |       | because density of 0.01 remains under threshold of 0.10.
stdout            | info    | Using sparse solver kinsol for nonlinear system 43 (7134),
|                 | |       | because density of 0.01 remains under threshold of 0.10.
stdout            | info    | The maximum density for using sparse solvers can be specified
|                 | |       | using the runtime flag '<-nlssMaxDensity=value>'.
stdout            | warning | Internal Numerical Jacobians without coloring are currently not supported by IDA with KLU. Colored numerical Jacobian will be used.
assert            | warning | The following assertion has been violated during initialization at time 0.000000
|                 | |       | 1e-08 * abs(bus1.QSlack) < 0.01
assert            | warning | The reactive power flowing into or out of the reference bus is above 0.01 pu.
|                 | |       | You probably need a better setup of excitation voltages, or you can set setPhaseOnly = true on the reference bus.
|                 | |       | Please check the documentation of ReferenceBus for further reference
assert            | warning | The following assertion has been violated during initialization at time 0.000000
|                 | |       | 1e-08 * abs(bus1.PSlack) < 0.01
assert            | warning | The active power flowing into or out of the reference bus is above 0.01 pu.
|                 | |       | You probably need a better balancing of the active power generators in the system.
|                 | |       | Please check the documentation of ReferenceBus for further reference
assert            | warning | The following assertion has been violated during initialization at time 0.000000
|                 | |       | bus1.IPuCheck < bus1.IPuMax
assert            | warning | Current too high (IPu=7.95425 > 2.5), check if the numerical solution is valid
LOG_SUCCESS       | info    | The initialization finished successfully with 3 homotopy steps.
LOG_STATS         | info    | ### STATISTICS ###
|                 | |       | | timer
|                 | |       | | |    0.0938728s          reading init.xml
|                 | |       | | |     0.010307s          reading info.xml
|                 | |       | | |     0.196717s [ 78.5%] pre-initialization
|                 | |       | | |    0.0054558s [  2.2%] initialization
|                 | |       | | |   2.7151e-05s [  0.0%] steps
|                 | |       | | |    0.0136188s [  5.4%] solver (excl. callbacks)
|                 | |       | | |    0.0066101s [  2.6%] creating output-file
|                 | |       | | |  0.000167898s [  0.1%] event-handling
|                 | |       | | |   0.00805916s [  3.2%] overhead
|                 | |       | | |    0.0198266s [  7.9%] simulation
|                 | |       | | |     0.250483s [100.0%] total
|                 | |       | | events
|                 | |       | | |     0 state events
|                 | |       | | |     0 time events
|                 | |       | | solver: ida
|                 | |       | | |    21 steps taken
|                 | |       | | |    21 calls of functionODE
|                 | |       | | |    19 evaluations of jacobian
|                 | |       | | |     0 error test failures
|                 | |       | | |     0 convergence test failures
|                 | |       | | | 0.00255905s time of jacobian evaluation
LOG_SUCCESS       | info    | The simulation finished successfully.