startTime=0
stopTime=1
tolerance=1e-06
numberOfIntervals=2500
stepSize=0.0004
wasm-jit simulation: simulate(PowerSysPro.Examples.OneProdLoadOneLineOneLineOneLoad,startTime=0,stopTime=1,tolerance=1e-06,numberOfIntervals=2500,outputFormat="empty",variableFilter="",fileNamePrefix="PowerSysPro_PowerSysPro.Examples.OneProdLoadOneLineOneLineOneLoad",simflags="-abortSlowSimulation -alarm=240   -lv LOG_STATS")
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/PowerSysPro 2.1.3/package.mo:41:7-41:140:writable]
|                 | |       | The following assertion has been violated during initialization at time 0.000000
|                 | |       | ((not (-pv.P) > (-pv.Pmax)), pv.P=-101407.24633312058, pv.Pmax=-1e4) --> ">>> Active power is above the maximum acceptable value for OneProdLoadOneLineOneLineOneLoad.pv"
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/PowerSysPro 2.1.3/package.mo:370:9-370:131:writable]
|                 | |       | The following assertion has been violated during initialization at time 0.000000
|                 | |       | ((not load.U < load.minU), load.U=19.726390960314124, load.minU=360.0) --> ">>> Voltage is below the minimum acceptable value for OneProdLoadOneLineOneLineOneLoad.load"
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/PowerSysPro 2.1.3/package.mo:143:9-143:152:writable]
|                 | |       | The following assertion has been violated during initialization at time 0.000000
|                 | |       | ((line1.IA <= 50.0), line1.IA=146.36882358778197) --> ">>> Current flowing the line is exceeding the maximum admissible current for OneProdLoadOneLineOneLineOneLoad.line1"
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/PowerSysPro 2.1.3/package.mo:143:9-143:152:writable]
|                 | |       | The following assertion has been violated during initialization at time 0.000000
|                 | |       | ((line2.IA <= 50.0), line2.IA=146.36882358778197) --> ">>> Current flowing the line is exceeding the maximum admissible current for OneProdLoadOneLineOneLineOneLoad.line2"
LOG_SUCCESS       | info    | The initialization finished successfully without homotopy method.
LOG_STATS         | info    | ### STATISTICS ###
|                 | |       | | timer
|                 | |       | | |            0s          reading init.xml
|                 | |       | | |            0s          reading info.xml
|                 | |       | | |   4.3922e-05s [  0.7%] pre-initialization
|                 | |       | | |  0.000248658s [  3.7%] initialization
|                 | |       | | |            0s [  0.0%] steps
|                 | |       | | |            0s [  0.0%] solver (excl. callbacks)
|                 | |       | | |    1.272e-06s [  0.0%] creating output-file
|                 | |       | | |            0s [  0.0%] event-handling
|                 | |       | | |            0s [  0.0%] overhead
|                 | |       | | |   0.00638551s [ 95.6%] simulation
|                 | |       | | |   0.00667936s [100.0%] total
|                 | |       | | events
|                 | |       | | |     0 state events
|                 | |       | | |     0 time events
|                 | |       | | solver: euler
|                 | |       | | |  2500 steps taken
|                 | |       | | |     0 calls of functionODE
|                 | |       | | |     0 evaluations of jacobian
|                 | |       | | |     0 error test failures
|                 | |       | | |     0 convergence test failures
|                 | |       | | | 0s time of jacobian evaluation
LOG_SUCCESS       | info    | The simulation finished successfully.