Environment - simulationEnvironment:
startTime=0
stopTime=100
tolerance=1e-06
numberOfIntervals=500
stepSize=0.2
Regular simulation: ./IDEAS_dev_IDEAS.Fluid.Actuators.Valves.Simplified.Examples.ThreeWayValveMotor  -abortSlowSimulation -alarm=480 -lv LOG_STATS
LOG_STDOUT        | info    | 
|                 | |       | Warning:
|                 | |       | ========
|                 | |       | It is recommended that the volume flow rate versus pressure relation
|                 | |       | of the fan or pump satisfies the minimum decrease condition
|                 | |       | 
|                 | |       |         (per.pressure.dp[i+1]-per.pressure.dp[i])
|                 | |       | d[i] = ------------------------------------------------- < -0
|                 | |       |        (per.pressure.V_flow[i+1]-per.pressure.V_flow[i])
|                 | |       | 
|                 | |       |  is
|                 | |       |   d[1]=0     
|                 | |       | 
|                 | |       | Otherwise, a solution to the equations may not exist if the fan or pump speed is reduced.
|                 | |       | In this situation, the solver will fail due to non-convergence and
|                 | |       | the simulation stops.
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/IDEAS 3.0.0-master/Fluid/Movers/BaseClasses/PartialFlowMachine.mo:348:3-357:39:writable]
|                 | |       | The following assertion has been violated during initialization at time 0.000000
|                 | |       | ((pumpFlow1.nominalValuesDefineDefaultPressureCurve)) --> "*** Warning: You are using a flow or pressure controlled mover with the
|                 | |       |              default pressure curve.
|                 | |       |              This leads to approximate calculations of the electrical power
|                 | |       |              consumption. Add the correct pressure curve in the record per
|                 | |       |              to obtain an accurate computation.
|                 | |       |              Setting nominalValuesDefineDefaultPressureCurve=true will suppress this warning."
LOG_SUCCESS       | info    | The initialization finished successfully without homotopy method.
LOG_STATS         | info    | ### STATISTICS ###
|                 | |       | | timer
|                 | |       | | |   0.00535445s          reading init.xml
|                 | |       | | |  0.000599474s          reading info.xml
|                 | |       | | |   5.7638e-05s [  3.2%] pre-initialization
|                 | |       | | |  0.000194294s [ 10.9%] initialization
|                 | |       | | |     9.72e-07s [  0.1%] steps
|                 | |       | | |      6.2e-07s [  0.0%] solver (excl. callbacks)
|                 | |       | | |            0s [  0.0%] creating output-file
|                 | |       | | |  -5.9557e-22s [ -0.0%] event-handling
|                 | |       | | |  0.000694286s [ 39.0%] overhead
|                 | |       | | |  0.000828833s [ 46.6%] simulation
|                 | |       | | |   0.00177955s [100.0%] total
|                 | |       | | events
|                 | |       | | |     0 state events
|                 | |       | | |     0 time events
|                 | |       | | solver: euler
|                 | |       | | |   500 steps taken
|                 | |       | | |   500 calls of functionODE
|                 | |       | | |     0 evaluations of jacobian
|                 | |       | | |     0 error test failures
|                 | |       | | |     0 convergence test failures
|                 | |       | | | 0s time of jacobian evaluation
LOG_SUCCESS       | info    | The simulation finished successfully.