(cd run_OMSimulator && /home/hudson/saved_omc/OMSimulator/install/bin/OMSimulator  --stripRoot --tempDir=temp_Buildings_13_Buildings_Fluid_DXSystems_Cooling_AirSource_Validation_SingleSpeedPLR_fmu --startTime=0 --stopTime=86400 --stepSize=34.56 --mode=me --timeout=240 --tolerance=1e-06 ../Buildings_13_Buildings_Fluid_DXSystems_Cooling_AirSource_Validation_SingleSpeedPLR.fmu)
info: *** FMU Simulation Info ***
     - model     : Buildings.Fluid.DXSystems.Cooling.AirSource.Validation.SingleSpeedPLR (model exchange)
     - fmiVersion: 2.0
     - startTime : 0.000000
     - stopTime  : 86400.000000
     - tolerance : 1e-06
     - stepSize  : 34.56
warning: [fmi2Warning] SingleSpeedPLR/logStatusWarning: /home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 13.0.2-maint.13.x/Fluid/DXSystems/Cooling/BaseClasses/Evaporation.mo:185: The following assertion has been violated during initialization at time 0.000000
         ((sinSpeDX.watVapEva.nomVal.gamma <= sinSpeDX.watVapEva.gammaMax), sinSpeDX.watVapEva.nomVal.gamma=1.5, sinSpeDX.watVapEva.gammaMax=0.3472586957788176) --> "*** Warning: In DX coil model, gamma is too large for these coil conditions.
             Instead of gamma = 1.5, a value of 0.347259, which
             corresponds to a mass transfer effectiveness of 0.8, will be used.
             Coil nominal performance data are:
             nomVal.m_flow_nominal = 1.72
             dX_nominal = XEvaOut_nominal-XEvaWetBulOut_nominal = 0.00562847 - 0.00620134 = -0.000572874
             QLat_flow_nominal  = -5677.29
info:    maximum step size for 'SingleSpeedPLR.root': 34.560000
info:    Result file: Buildings_13_Buildings_Fluid_DXSystems_Cooling_AirSource_Validation_SingleSpeedPLR_res.mat (bufferSize=10)
info:    Parameter SingleSpeedPLR.onOff.combiTimeTable.delimiter will not be stored in the result file, because the signal type is not supported
info:    Parameter SingleSpeedPLR.onOff.combiTimeTable.fileName will not be stored in the result file, because the signal type is not supported
info:    Parameter SingleSpeedPLR.onOff.combiTimeTable.tableName will not be stored in the result file, because the signal type is not supported
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 13.0.2-maint.13.x/Fluid/DXSystems/Cooling/BaseClasses/PartialCapacity.mo:121:7-134:38:writable]
|                 | |       | The following assertion has been violated at time 25200.000000
|                 | |       | ((not (sinSpeDX.dxCoi.TEvaIn > sinSpeDX.dxCoi.dryCoi.coiCap.sta[1].perCur.TEvaInMax or sinSpeDX.dxCoi.TEvaIn < sinSpeDX.dxCoi.dryCoi.coiCap.sta[1].perCur.TEvaInMin)), sinSpeDX.dxCoi.TEvaIn=297.23651629, sinSpeDX.dxCoi.dryCoi.coiCap.sta[1].perCur.TEvaInMax=297.03889, sinSpeDX.dxCoi.dryCoi.coiCap.sta[1].perCur.TEvaInMin=285.92778) --> "*** Warning: Evaporator temperature TEvaIn is out of bounds in DX coil model at time = 25200.
|                 | |       |     stage     = 1
|                 | |       |     TEvaInMin = 285.928 Kelvin (12.7778 degC)
|                 | |       |     TEvaIn    = 297.237 Kelvin (24.0865 degC)
|                 | |       |     TEvaInMax = 297.039 Kelvin (23.8889 degC)
|                 | |       |     Extrapolation can introduce large errors.
|                 | |       |     This warning will only be reported once for each stage."
info:    Final Statistics for 'SingleSpeedPLR.root':
         NumSteps = 0 NumRhsEvals  = 0 NumLinSolvSetups = 0
         NumNonlinSolvIters = 0 NumNonlinSolvConvFails = 0 NumErrTestFails = 0
info:    1 warnings
info:    0 errors