python3 -m fmpy simulate  --output-file Buildings_8_Buildings.Obsolete.DistrictHeatingCooling.SubStations.VaporCompression.Validation.HeatingCoolingHotwaterTimeSeries_dT_res.csv --start-time 0 --stop-time 864000 --timeout 50 --relative-tolerance 1e-08 Buildings_8_Buildings_Obsolete_DistrictHeatingCooling_SubStations_VaporCompression_Validation_HeatingCoolingHotwaterTimeSeries_dT.fmu
LOG_STDOUT        | info    | ... loading "tab1" from "/tmp/tmpmux7tufc/resources/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 8.1.4-maint.8.1.x/Resources/Data/Obsolete/DistrictHeatingCooling/SubStations/VaporCompression/RefBldgLargeOfficeNew2004_7.1_5.0_3C_USA_CA_SAN_FRANCISCO.mos"
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 8.1.4-maint.8.1.x/Fluid/Movers/BaseClasses/PartialFlowMachine.mo:352:3-361:39:writable]
|                 | |       | The following assertion has been violated during initialization at time 0.000000
|                 | |       | ((subSta.pumHea.nominalValuesDefineDefaultPressureCurve)) --> "*** Warning: You are using a flow or pressure controlled mover with the
|                 | |       |              default pressure curve.
|                 | |       |              This leads to approximate calculations of the electrical power
|                 | |       |              consumption. Add the correct pressure curve in the record per
|                 | |       |              to obtain an accurate computation.
|                 | |       |              Setting nominalValuesDefineDefaultPressureCurve=true will suppress this warning."
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 8.1.4-maint.8.1.x/Fluid/Movers/BaseClasses/PartialFlowMachine.mo:352:3-361:39:writable]
|                 | |       | The following assertion has been violated during initialization at time 0.000000
|                 | |       | ((subSta.pumHotWat.nominalValuesDefineDefaultPressureCurve)) --> "*** Warning: You are using a flow or pressure controlled mover with the
|                 | |       |              default pressure curve.
|                 | |       |              This leads to approximate calculations of the electrical power
|                 | |       |              consumption. Add the correct pressure curve in the record per
|                 | |       |              to obtain an accurate computation.
|                 | |       |              Setting nominalValuesDefineDefaultPressureCurve=true will suppress this warning."
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 8.1.4-maint.8.1.x/Fluid/Movers/BaseClasses/PartialFlowMachine.mo:352:3-361:39:writable]
|                 | |       | The following assertion has been violated during initialization at time 0.000000
|                 | |       | ((subSta.pumChi.nominalValuesDefineDefaultPressureCurve)) --> "*** Warning: You are using a flow or pressure controlled mover with the
|                 | |       |              default pressure curve.
|                 | |       |              This leads to approximate calculations of the electrical power
|                 | |       |              consumption. Add the correct pressure curve in the record per
|                 | |       |              to obtain an accurate computation.
|                 | |       |              Setting nominalValuesDefineDefaultPressureCurve=true will suppress this warning."
LOG_ASSERT        | error   | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 8.1.4-maint.8.1.x/Fluid/Interfaces/StaticTwoPortConservationEquation.mo:144:5-152:68:writable]
|                 | |       | The following assertion has been violated at time 645000.000000
|                 | |       | ((noEvent(abs(subSta.heaPum.eva.Q_flow) < 836800.0 * max(0.001 * subSta.heaPum.eva.vol.steBal.m_flow_small, abs(subSta.heaPum.m2_flow))))) --> "In HeatingCoolingHotwaterTimeSeries_dT.subSta.heaPum.eva.vol.steBal:
|                 | |       |    The heat flow rate equals 4.31412 W and the mass flow rate equals -1.78397e-06 kg/s,
|                 | |       |    which results in a temperature difference 282.546 K > dTMax=200 K.
|                 | |       |    This may indicate that energy is not conserved for small mass flow rates.
|                 | |       |    The implementation may require prescribedHeatFlowRate = false."
Traceback (most recent call last):
  File "/usr/lib/python3.10/runpy.py", line 196, in _run_module_as_main
    return _run_code(code, main_globals, None,
  File "/usr/lib/python3.10/runpy.py", line 86, in _run_code
    exec(code, run_globals)
  File "/usr/local/lib/python3.10/dist-packages/fmpy/__main__.py", line 4, in <module>
    main()
  File "/usr/local/lib/python3.10/dist-packages/fmpy/command_line.py", line 167, in main
    result = simulate_fmu(args.fmu_filename,
  File "/usr/local/lib/python3.10/dist-packages/fmpy/simulation.py", line 759, in simulate_fmu
    result = simulateME(model_description, fmu, start_time, stop_time, solver, step_size, relative_tolerance, start_values, apply_default_start_values, input, output, output_interval, record_events, timeout, step_finished, validate, set_stop_time)
  File "/usr/local/lib/python3.10/dist-packages/fmpy/simulation.py", line 1076, in simulateME
    step_event, _ = fmu.completedIntegratorStep()
  File "/usr/local/lib/python3.10/dist-packages/fmpy/fmi2.py", line 491, in completedIntegratorStep
    self.fmi2CompletedIntegratorStep(self.component, noSetFMUStatePriorToCurrentPoint, byref(enterEventMode), byref(terminateSimulation))
  File "/usr/local/lib/python3.10/dist-packages/fmpy/fmi2.py", line 215, in w
    raise FMICallException(function=fname, status=res)
fmpy.fmi1.FMICallException: fmi2CompletedIntegratorStep failed with status 3 (error).