(cd run_OMSimulator-cs-euler && /home/hudson/saved_omc/OMSimulator/install/bin/OMSimulator --resultFile=../Buildings_latest_Buildings.Examples.Tutorial.Boiler.System5_OMSimulator-cs-euler_res.mat --stripRoot --tempDir=temp_Buildings_latest_Buildings_Examples_Tutorial_Boiler_System5_OMSimulator-cs-euler_fmu --startTime=0 --stopTime=172800 --stepSize=69.12 --mode=cs --timeout=240 --tolerance=1e-06 ../Buildings_latest_Buildings_Examples_Tutorial_Boiler_System5_OMSimulator-cs-euler.fmu)
info: *** FMU Simulation Info ***
     - model     : Buildings.Examples.Tutorial.Boiler.System5 (co-simulation)
     - fmiVersion: 2.0
     - startTime : 0.000000
     - stopTime  : 172800.000000
     - tolerance : 1e-06
     - stepSize  : 69.12
info:    Result file: ../Buildings_latest_Buildings.Examples.Tutorial.Boiler.System5_OMSimulator-cs-euler_res.mat (bufferSize=10)
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 15.0.0-master/Fluid/Movers/FlowControlled_m_flow.mo:87:3-92:58:writable]
|                 | |       | The following assertion has been violated at time 69.120000
|                 | |       | ((pumBoi.dpMachine <= pumBoi.dpMax), pumBoi.dpMachine=133038.8184872433, pumBoi.dpMax=40000) --> "In System5.pumBoi: Model operates with head -dp = 133039 Pa,
|                 | |       |     exceeding the pressure allowed by the parameter System5.pumBoi.dpMax.
|                 | |       |     This can happen if the model forces a high mass flow rate through a closed actuator,
|                 | |       |     or if the performance record is unreasonable. Please verify your model, and
|                 | |       |     consider using one of the other pump or fan models."
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 15.0.0-master/Fluid/Movers/FlowControlled_m_flow.mo:87:3-92:58:writable]
|                 | |       | The following assertion has been violated at time 69.120000
|                 | |       | (((-pumRad.dp) <= pumRad.dpMax), pumRad.dp=-78051.40062367165, pumRad.dpMax=40000) --> "In System5.pumRad: Model operates with head -dp = 78051.4 Pa,
|                 | |       |     exceeding the pressure allowed by the parameter System5.pumRad.dpMax.
|                 | |       |     This can happen if the model forces a high mass flow rate through a closed actuator,
|                 | |       |     or if the performance record is unreasonable. Please verify your model, and
|                 | |       |     consider using one of the other pump or fan models."
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 15.0.0-master/Fluid/Movers/FlowControlled_m_flow.mo:87:3-92:58:writable]
|                 | |       | The following assertion has been violated at time 69.120000
|                 | |       | (((-pumRad.dp) <= pumRad.dpMax), pumRad.dp=-78051.40062367165, pumRad.dpMax=40000) --> "In System5.pumRad: Model operates with head -dp = 78051.4 Pa,
|                 | |       |     exceeding the pressure allowed by the parameter System5.pumRad.dpMax.
|                 | |       |     This can happen if the model forces a high mass flow rate through a closed actuator,
|                 | |       |     or if the performance record is unreasonable. Please verify your model, and
|                 | |       |     consider using one of the other pump or fan models."
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 15.0.0-master/Fluid/Movers/FlowControlled_m_flow.mo:87:3-92:58:writable]
|                 | |       | The following assertion has been violated at time 69.120000
|                 | |       | ((pumBoi.dpMachine <= pumBoi.dpMax), pumBoi.dpMachine=133038.8184872433, pumBoi.dpMax=40000) --> "In System5.pumBoi: Model operates with head -dp = 133039 Pa,
|                 | |       |     exceeding the pressure allowed by the parameter System5.pumBoi.dpMax.
|                 | |       |     This can happen if the model forces a high mass flow rate through a closed actuator,
|                 | |       |     or if the performance record is unreasonable. Please verify your model, and
|                 | |       |     consider using one of the other pump or fan models."
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 15.0.0-master/Fluid/Movers/FlowControlled_m_flow.mo:87:3-92:58:writable]
|                 | |       | The following assertion has been violated at time 69.120000
|                 | |       | (((-pumRad.dp) <= pumRad.dpMax), pumRad.dp=-78051.40062367165, pumRad.dpMax=40000) --> "In System5.pumRad: Model operates with head -dp = 78051.4 Pa,
|                 | |       |     exceeding the pressure allowed by the parameter System5.pumRad.dpMax.
|                 | |       |     This can happen if the model forces a high mass flow rate through a closed actuator,
|                 | |       |     or if the performance record is unreasonable. Please verify your model, and
|                 | |       |     consider using one of the other pump or fan models."
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 15.0.0-master/Fluid/Movers/FlowControlled_m_flow.mo:87:3-92:58:writable]
|                 | |       | The following assertion has been violated at time 69.120000
|                 | |       | ((pumBoi.dpMachine <= pumBoi.dpMax), pumBoi.dpMachine=133038.8184872433, pumBoi.dpMax=40000) --> "In System5.pumBoi: Model operates with head -dp = 133039 Pa,
|                 | |       |     exceeding the pressure allowed by the parameter System5.pumBoi.dpMax.
|                 | |       |     This can happen if the model forces a high mass flow rate through a closed actuator,
|                 | |       |     or if the performance record is unreasonable. Please verify your model, and
|                 | |       |     consider using one of the other pump or fan models."
LOG_ASSERT        | error   | No event found, but assert was triggered. Throwing now!
error:   [fmi2logger] [fmi2Error] System5/logStatusError: /home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 15.0.0-master/Fluid/Movers/FlowControlled_m_flow.mo:87: The following assertion has been violated at time 69.120000
         ((pumBoi.dpMachine <= pumBoi.dpMax), pumBoi.dpMachine=133038.8184872433, pumBoi.dpMax=40000) --> "In System5.pumBoi: Model operates with head -dp = 133039 Pa,
             exceeding the pressure allowed by the parameter System5.pumBoi.dpMax.
             This can happen if the model forces a high mass flow rate through a closed actuator,
             or if the performance record is unreasonable. Please verify your model, and
             consider using one of the other pump or fan models."
error:   [fmi2logger] [fmi2Error] System5/logFmi2Call: internalEventUpdate: terminated by an assertion.
error:   [stepUntil] fmi2_doStep failed for FMU "System5.root.System5"
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 15.0.0-master/Fluid/Movers/FlowControlled_m_flow.mo:87:3-92:58:writable]
|                 | |       | The following assertion has been violated at time 69.120000
|                 | |       | ((pumBoi.dpMachine <= pumBoi.dpMax), pumBoi.dpMachine=133038.8184872433, pumBoi.dpMax=40000) --> "In System5.pumBoi: Model operates with head -dp = 133039 Pa,
|                 | |       |     exceeding the pressure allowed by the parameter System5.pumBoi.dpMax.
|                 | |       |     This can happen if the model forces a high mass flow rate through a closed actuator,
|                 | |       |     or if the performance record is unreasonable. Please verify your model, and
|                 | |       |     consider using one of the other pump or fan models."
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 15.0.0-master/Fluid/Movers/FlowControlled_m_flow.mo:87:3-92:58:writable]
|                 | |       | The following assertion has been violated at time 69.120000
|                 | |       | (((-pumRad.dp) <= pumRad.dpMax), pumRad.dp=-78051.40062367165, pumRad.dpMax=40000) --> "In System5.pumRad: Model operates with head -dp = 78051.4 Pa,
|                 | |       |     exceeding the pressure allowed by the parameter System5.pumRad.dpMax.
|                 | |       |     This can happen if the model forces a high mass flow rate through a closed actuator,
|                 | |       |     or if the performance record is unreasonable. Please verify your model, and
|                 | |       |     consider using one of the other pump or fan models."
Traceback (most recent call last):
  File "<frozen runpy>", line 198, in _run_module_as_main
  File "<frozen runpy>", line 88, in _run_code
  File "/home/hudson/saved_omc/OMSimulator/install/lib/x86_64-linux-gnu/OMSimulator/__main__.py", line 38, in <module>
    sys.exit(main())
             ~~~~^^
  File "/home/hudson/saved_omc/OMSimulator/install/lib/x86_64-linux-gnu/OMSimulator/cli.py", line 309, in main
    handler(args.model, args)
    ~~~~~~~^^^^^^^^^^^^^^^^^^
  File "/home/hudson/saved_omc/OMSimulator/install/lib/x86_64-linux-gnu/OMSimulator/cli.py", line 176, in _runFMU
    fmu.simulate()
    ~~~~~~~~~~~~^^
  File "/home/hudson/saved_omc/OMSimulator/install/lib/x86_64-linux-gnu/OMSimulator/fmu.py", line 906, in simulate
    raise RuntimeError(f"Failed to simulate model: {status}")
RuntimeError: Failed to simulate model: Status.error
info:    0 warnings
info:    3 errors