(cd run_OMSimulator-cs-euler && /home/hudson/saved_omc/OMSimulator/install/bin/OMSimulator --stripRoot --tempDir=temp_Buildings_13_Buildings_Fluid_HeatExchangers_CoolingTowers_Examples_FixedApproachWetBulb_OMSimulator-cs-euler_fmu --startTime=1.5552e+07 --stopTime=1.5984e+07 --stepSize=172.8 --mode=cs --timeout=240 --tolerance=1e-06 ../Buildings_13_Buildings_Fluid_HeatExchangers_CoolingTowers_Examples_FixedApproachWetBulb_OMSimulator-cs-euler.fmu) info: *** FMU Simulation Info *** - model : Buildings.Fluid.HeatExchangers.CoolingTowers.Examples.FixedApproachWetBulb (co-simulation) - fmiVersion: 2.0 - startTime : 15552000.000000 - stopTime : 15984000.000000 - tolerance : 1e-06 - stepSize : 172.8 info: Result file: Buildings_13_Buildings_Fluid_HeatExchangers_CoolingTowers_Examples_FixedApproachWetBulb_OMSimulator-cs-euler_res.mat (bufferSize=10) info: Parameter FixedApproachWetBulb.weaDat.filNam will not be stored in the result file, because the signal type is not supported LOG_ASSERT | info | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 13.0.2-maint.13.x/Fluid/Movers/FlowControlled_m_flow.mo:87:3-92:58:writable] | | | | The following assertion has been violated at time 15553382.400000 | | | | (((-pum.dp) <= pum.dpMax), pum.dp=-246395.3583159441, pum.dpMax=40000) --> "In FixedApproachWetBulb.pum: Model operates with head -dp = 246395 Pa, | | | | exceeding the pressure allowed by the parameter FixedApproachWetBulb.pum.dpMax. | | | | This can happen if the model forces a high mass flow rate through a closed actuator, | | | | or if the performance record is unreasonable. Please verify your model, and | | | | consider using one of the other pump or fan models." LOG_ASSERT | info | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 13.0.2-maint.13.x/Media/Water.mo:66:5-67:122:writable] | | | | The following assertion has been violated at time 15553382.400000 | | | | ((noEvent(pum.vol.dynBal.medium.T <= 403.15)), pum.vol.dynBal.medium.T=634.8418107012617) --> "In FixedApproachWetBulb.pum.vol.dynBal.medium: Temperature T = 634.842 K exceeded its maximum allowed value of 130 degC (403.15 Kelvin) as required from medium model "Buildings.Media.Water"." LOG_ASSERT | info | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 13.0.2-maint.13.x/Media/Water.mo:63:5-64:122:writable] | | | | The following assertion has been violated at time 15553382.400000 | | | | ((noEvent(tow.vol.dynBal.medium.T >= 272.15)), tow.vol.dynBal.medium.T=271.550406618396) --> "In FixedApproachWetBulb.tow.vol.dynBal.medium: Temperature T = 271.55 K exceeded its minimum allowed value of -1 degC (272.15 Kelvin) as required from medium model "Buildings.Media.Water"." LOG_ASSERT | info | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 13.0.2-maint.13.x/Media/Water.mo:63:5-64:122:writable] | | | | The following assertion has been violated at time 15553382.400000 | | | | ((noEvent(tow.vol.dynBal.medium.T >= 272.15)), tow.vol.dynBal.medium.T=271.550406618396) --> "In FixedApproachWetBulb.tow.vol.dynBal.medium: Temperature T = 271.55 K exceeded its minimum allowed value of -1 degC (272.15 Kelvin) as required from medium model "Buildings.Media.Water"." LOG_ASSERT | info | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 13.0.2-maint.13.x/Media/Water.mo:66:5-67:122:writable] | | | | The following assertion has been violated at time 15553382.400000 | | | | ((noEvent(pum.vol.dynBal.medium.T <= 403.15)), pum.vol.dynBal.medium.T=634.8418107012617) --> "In FixedApproachWetBulb.pum.vol.dynBal.medium: Temperature T = 634.842 K exceeded its maximum allowed value of 130 degC (403.15 Kelvin) as required from medium model "Buildings.Media.Water"." LOG_ASSERT | info | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 13.0.2-maint.13.x/Fluid/Movers/FlowControlled_m_flow.mo:87:3-92:58:writable] | | | | The following assertion has been violated at time 15553382.400000 | | | | (((-pum.dp) <= pum.dpMax), pum.dp=-246395.3583159441, pum.dpMax=40000) --> "In FixedApproachWetBulb.pum: Model operates with head -dp = 246395 Pa, | | | | exceeding the pressure allowed by the parameter FixedApproachWetBulb.pum.dpMax. | | | | This can happen if the model forces a high mass flow rate through a closed actuator, | | | | or if the performance record is unreasonable. Please verify your model, and | | | | consider using one of the other pump or fan models." LOG_ASSERT | info | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 13.0.2-maint.13.x/Media/Water.mo:63:5-64:122:writable] | | | | The following assertion has been violated at time 15553382.400000 | | | | ((noEvent(tow.vol.dynBal.medium.T >= 272.15)), tow.vol.dynBal.medium.T=271.550406618396) --> "In FixedApproachWetBulb.tow.vol.dynBal.medium: Temperature T = 271.55 K exceeded its minimum allowed value of -1 degC (272.15 Kelvin) as required from medium model "Buildings.Media.Water"." LOG_ASSERT | info | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 13.0.2-maint.13.x/Media/Water.mo:66:5-67:122:writable] | | | | The following assertion has been violated at time 15553382.400000 | | | | ((noEvent(pum.vol.dynBal.medium.T <= 403.15)), pum.vol.dynBal.medium.T=634.8418107012617) --> "In FixedApproachWetBulb.pum.vol.dynBal.medium: Temperature T = 634.842 K exceeded its maximum allowed value of 130 degC (403.15 Kelvin) as required from medium model "Buildings.Media.Water"." LOG_ASSERT | info | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 13.0.2-maint.13.x/Fluid/Movers/FlowControlled_m_flow.mo:87:3-92:58:writable] | | | | The following assertion has been violated at time 15553382.400000 | | | | (((-pum.dp) <= pum.dpMax), pum.dp=-246395.3583159441, pum.dpMax=40000) --> "In FixedApproachWetBulb.pum: Model operates with head -dp = 246395 Pa, | | | | exceeding the pressure allowed by the parameter FixedApproachWetBulb.pum.dpMax. | | | | This can happen if the model forces a high mass flow rate through a closed actuator, | | | | or if the performance record is unreasonable. Please verify your model, and | | | | consider using one of the other pump or fan models." LOG_ASSERT | error | No event found, but assert was triggered. Throwing now! error: [fmi2logger] [fmi2Error] FixedApproachWetBulb/logStatusError: /home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 13.0.2-maint.13.x/Fluid/Movers/FlowControlled_m_flow.mo:87: The following assertion has been violated at time 15553382.400000 (((-pum.dp) <= pum.dpMax), pum.dp=-246395.3583159441, pum.dpMax=40000) --> "In FixedApproachWetBulb.pum: Model operates with head -dp = 246395 Pa, exceeding the pressure allowed by the parameter FixedApproachWetBulb.pum.dpMax. This can happen if the model forces a high mass flow rate through a closed actuator, or if the performance record is unreasonable. Please verify your model, and consider using one of the other pump or fan models." error: [fmi2logger] [fmi2Error] FixedApproachWetBulb/logFmi2Call: internalEventUpdate: terminated by an assertion. error: [stepUntil] fmi2_doStep failed for FMU "FixedApproachWetBulb.root.FixedApproachWetBulb" LOG_ASSERT | info | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 13.0.2-maint.13.x/Fluid/Movers/FlowControlled_m_flow.mo:87:3-92:58:writable] | | | | The following assertion has been violated at time 15553382.400000 | | | | (((-pum.dp) <= pum.dpMax), pum.dp=-246395.3583159441, pum.dpMax=40000) --> "In FixedApproachWetBulb.pum: Model operates with head -dp = 246395 Pa, | | | | exceeding the pressure allowed by the parameter FixedApproachWetBulb.pum.dpMax. | | | | This can happen if the model forces a high mass flow rate through a closed actuator, | | | | or if the performance record is unreasonable. Please verify your model, and | | | | consider using one of the other pump or fan models." LOG_ASSERT | info | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 13.0.2-maint.13.x/Media/Water.mo:66:5-67:122:writable] | | | | The following assertion has been violated at time 15553382.400000 | | | | ((noEvent(pum.vol.dynBal.medium.T <= 403.15)), pum.vol.dynBal.medium.T=634.8418107012617) --> "In FixedApproachWetBulb.pum.vol.dynBal.medium: Temperature T = 634.842 K exceeded its maximum allowed value of 130 degC (403.15 Kelvin) as required from medium model "Buildings.Media.Water"." LOG_ASSERT | info | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 13.0.2-maint.13.x/Media/Water.mo:63:5-64:122:writable] | | | | The following assertion has been violated at time 15553382.400000 | | | | ((noEvent(tow.vol.dynBal.medium.T >= 272.15)), tow.vol.dynBal.medium.T=271.550406618396) --> "In FixedApproachWetBulb.tow.vol.dynBal.medium: Temperature T = 271.55 K exceeded its minimum allowed value of -1 degC (272.15 Kelvin) as required from medium model "Buildings.Media.Water"." Traceback (most recent call last): File "", line 198, in _run_module_as_main File "", line 88, in _run_code File "/home/hudson/saved_omc/OMSimulator/install/lib/x86_64-linux-gnu/OMSimulator/__main__.py", line 38, in sys.exit(main()) ~~~~^^ File "/home/hudson/saved_omc/OMSimulator/install/lib/x86_64-linux-gnu/OMSimulator/cli.py", line 309, in main handler(args.model, args) ~~~~~~~^^^^^^^^^^^^^^^^^^ File "/home/hudson/saved_omc/OMSimulator/install/lib/x86_64-linux-gnu/OMSimulator/cli.py", line 176, in _runFMU fmu.simulate() ~~~~~~~~~~~~^^ File "/home/hudson/saved_omc/OMSimulator/install/lib/x86_64-linux-gnu/OMSimulator/fmu.py", line 906, in simulate raise RuntimeError(f"Failed to simulate model: {status}") RuntimeError: Failed to simulate model: Status.error info: 0 warnings info: 3 errors