(cd run_OMSimulator-cs-euler && /home/hudson/saved_omc/OMSimulator/install/bin/OMSimulator --resultFile=../Buildings_12_Buildings.Examples.Tutorial.SpaceCooling.System3_OMSimulator-cs-euler_res.mat --stripRoot --tempDir=temp_Buildings_12_Buildings_Examples_Tutorial_SpaceCooling_System3_OMSimulator-cs-euler_fmu --startTime=1.5552e+07 --stopTime=1.56384e+07 --stepSize=34.56 --mode=cs --timeout=240 --tolerance=1e-06 ../Buildings_12_Buildings_Examples_Tutorial_SpaceCooling_System3_OMSimulator-cs-euler.fmu)
info: *** FMU Simulation Info ***
     - model     : Buildings.Examples.Tutorial.SpaceCooling.System3 (co-simulation)
     - fmiVersion: 2.0
     - startTime : 15552000.000000
     - stopTime  : 15638400.000000
     - tolerance : 1e-06
     - stepSize  : 34.56
info:    Result file: ../Buildings_12_Buildings.Examples.Tutorial.SpaceCooling.System3_OMSimulator-cs-euler_res.mat (bufferSize=10)
info:    Parameter System3.weaDat.filNam will not be stored in the result file, because the signal type is not supported
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Media/Air.mo:154:3-154:148:writable]
|                 | |       | The following assertion has been violated at time 15552069.120000
|                 | |       | ((noEvent(cooCoi.heaCooHum_u.vol.dynBal.medium.p >= 0.0)), cooCoi.heaCooHum_u.vol.dynBal.medium.p=-33143.8128040585) --> "Pressure (= -33143.8 Pa) of medium "Buildings.Media.Air" is negative
|                 | |       | (Temperature = 667.94 K)"
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Media/Air.mo:151:5-152:57:writable]
|                 | |       | The following assertion has been violated at time 15552069.120000
|                 | |       | ((noEvent(cooCoi.heaCooHum_u.vol.dynBal.medium.T <= 423.15)), cooCoi.heaCooHum_u.vol.dynBal.medium.T=667.9400126516643) --> "In System3.cooCoi.heaCooHum_u.vol.dynBal.medium: Temperature T exceeded its maximum allowed value of 150 degC (423.15 Kelvin)
|                 | |       | as required from medium model "Buildings.Media.Air"."
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Media/Air.mo:146:5-147:72:writable]
|                 | |       | The following assertion has been violated at time 15552069.120000
|                 | |       | ((noEvent(cooCoi.heaCooHum_u.vol.dynBal.medium.Xi[1] >= -1e-5) and noEvent(cooCoi.heaCooHum_u.vol.dynBal.medium.Xi[1] <= 1.00001)), cooCoi.heaCooHum_u.vol.dynBal.medium.Xi[1]=-0.003271040000400544) --> "Mass fraction X[1] = -0.00327104 of substance water
|                 | |       | of medium "Buildings.Media.Air" is not in the range 0..1"
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Fluid/Movers/FlowControlled_m_flow.mo:87:3-92:58:writable]
|                 | |       | The following assertion has been violated at time 15552069.120000
|                 | |       | (((-fan.dp) <= fan.dpMax), fan.dp=-146535.9555479615, fan.dpMax=2000) --> "In System3.fan: Model operates with head -dp = 146536 Pa,
|                 | |       |     exceeding the pressure allowed by the parameter System3.fan.dpMax.
|                 | |       |     This can happen if the model forces a high mass flow rate through a closed actuator,
|                 | |       |     or if the performance record is unreasonable. Please verify your model, and
|                 | |       |     consider using one of the other pump or fan models."
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Fluid/Movers/FlowControlled_m_flow.mo:87:3-92:58:writable]
|                 | |       | The following assertion has been violated at time 15552069.120000
|                 | |       | (((-fan.dp) <= fan.dpMax), fan.dp=-146535.9555479615, fan.dpMax=2000) --> "In System3.fan: Model operates with head -dp = 146536 Pa,
|                 | |       |     exceeding the pressure allowed by the parameter System3.fan.dpMax.
|                 | |       |     This can happen if the model forces a high mass flow rate through a closed actuator,
|                 | |       |     or if the performance record is unreasonable. Please verify your model, and
|                 | |       |     consider using one of the other pump or fan models."
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Media/Air.mo:146:5-147:72:writable]
|                 | |       | The following assertion has been violated at time 15552069.120000
|                 | |       | ((noEvent(cooCoi.heaCooHum_u.vol.dynBal.medium.Xi[1] >= -1e-5) and noEvent(cooCoi.heaCooHum_u.vol.dynBal.medium.Xi[1] <= 1.00001)), cooCoi.heaCooHum_u.vol.dynBal.medium.Xi[1]=-0.003271040000400544) --> "Mass fraction X[1] = -0.00327104 of substance water
|                 | |       | of medium "Buildings.Media.Air" is not in the range 0..1"
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Media/Air.mo:151:5-152:57:writable]
|                 | |       | The following assertion has been violated at time 15552069.120000
|                 | |       | ((noEvent(cooCoi.heaCooHum_u.vol.dynBal.medium.T <= 423.15)), cooCoi.heaCooHum_u.vol.dynBal.medium.T=667.9400126516643) --> "In System3.cooCoi.heaCooHum_u.vol.dynBal.medium: Temperature T exceeded its maximum allowed value of 150 degC (423.15 Kelvin)
|                 | |       | as required from medium model "Buildings.Media.Air"."
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Media/Air.mo:154:3-154:148:writable]
|                 | |       | The following assertion has been violated at time 15552069.120000
|                 | |       | ((noEvent(cooCoi.heaCooHum_u.vol.dynBal.medium.p >= 0.0)), cooCoi.heaCooHum_u.vol.dynBal.medium.p=-33143.8128040585) --> "Pressure (= -33143.8 Pa) of medium "Buildings.Media.Air" is negative
|                 | |       | (Temperature = 667.94 K)"
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Fluid/Movers/FlowControlled_m_flow.mo:87:3-92:58:writable]
|                 | |       | The following assertion has been violated at time 15552069.120000
|                 | |       | (((-fan.dp) <= fan.dpMax), fan.dp=-146535.9555479615, fan.dpMax=2000) --> "In System3.fan: Model operates with head -dp = 146536 Pa,
|                 | |       |     exceeding the pressure allowed by the parameter System3.fan.dpMax.
|                 | |       |     This can happen if the model forces a high mass flow rate through a closed actuator,
|                 | |       |     or if the performance record is unreasonable. Please verify your model, and
|                 | |       |     consider using one of the other pump or fan models."
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Media/Air.mo:146:5-147:72:writable]
|                 | |       | The following assertion has been violated at time 15552069.120000
|                 | |       | ((noEvent(cooCoi.heaCooHum_u.vol.dynBal.medium.Xi[1] >= -1e-5) and noEvent(cooCoi.heaCooHum_u.vol.dynBal.medium.Xi[1] <= 1.00001)), cooCoi.heaCooHum_u.vol.dynBal.medium.Xi[1]=-0.003271040000400544) --> "Mass fraction X[1] = -0.00327104 of substance water
|                 | |       | of medium "Buildings.Media.Air" is not in the range 0..1"
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Media/Air.mo:151:5-152:57:writable]
|                 | |       | The following assertion has been violated at time 15552069.120000
|                 | |       | ((noEvent(cooCoi.heaCooHum_u.vol.dynBal.medium.T <= 423.15)), cooCoi.heaCooHum_u.vol.dynBal.medium.T=667.9400126516643) --> "In System3.cooCoi.heaCooHum_u.vol.dynBal.medium: Temperature T exceeded its maximum allowed value of 150 degC (423.15 Kelvin)
|                 | |       | as required from medium model "Buildings.Media.Air"."
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Media/Air.mo:154:3-154:148:writable]
|                 | |       | The following assertion has been violated at time 15552069.120000
|                 | |       | ((noEvent(cooCoi.heaCooHum_u.vol.dynBal.medium.p >= 0.0)), cooCoi.heaCooHum_u.vol.dynBal.medium.p=-33143.8128040585) --> "Pressure (= -33143.8 Pa) of medium "Buildings.Media.Air" is negative
|                 | |       | (Temperature = 667.94 K)"
LOG_ASSERT        | error   | No event found, but assert was triggered. Throwing now!
error:   [fmi2logger] [fmi2Error] System3/logStatusError: /home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Media/Air.mo:154: The following assertion has been violated at time 15552069.120000
         ((noEvent(cooCoi.heaCooHum_u.vol.dynBal.medium.p >= 0.0)), cooCoi.heaCooHum_u.vol.dynBal.medium.p=-33143.8128040585) --> "Pressure (= -33143.8 Pa) of medium "Buildings.Media.Air" is negative
         (Temperature = 667.94 K)"
error:   [fmi2logger] [fmi2Error] System3/logFmi2Call: internalEventUpdate: terminated by an assertion.
error:   [stepUntil] fmi2_doStep failed for FMU "System3.root.System3"
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Media/Air.mo:154:3-154:148:writable]
|                 | |       | The following assertion has been violated at time 15552069.120000
|                 | |       | ((noEvent(cooCoi.heaCooHum_u.vol.dynBal.medium.p >= 0.0)), cooCoi.heaCooHum_u.vol.dynBal.medium.p=-33143.8128040585) --> "Pressure (= -33143.8 Pa) of medium "Buildings.Media.Air" is negative
|                 | |       | (Temperature = 667.94 K)"
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Media/Air.mo:151:5-152:57:writable]
|                 | |       | The following assertion has been violated at time 15552069.120000
|                 | |       | ((noEvent(cooCoi.heaCooHum_u.vol.dynBal.medium.T <= 423.15)), cooCoi.heaCooHum_u.vol.dynBal.medium.T=667.9400126516643) --> "In System3.cooCoi.heaCooHum_u.vol.dynBal.medium: Temperature T exceeded its maximum allowed value of 150 degC (423.15 Kelvin)
|                 | |       | as required from medium model "Buildings.Media.Air"."
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Media/Air.mo:146:5-147:72:writable]
|                 | |       | The following assertion has been violated at time 15552069.120000
|                 | |       | ((noEvent(cooCoi.heaCooHum_u.vol.dynBal.medium.Xi[1] >= -1e-5) and noEvent(cooCoi.heaCooHum_u.vol.dynBal.medium.Xi[1] <= 1.00001)), cooCoi.heaCooHum_u.vol.dynBal.medium.Xi[1]=-0.003271040000400544) --> "Mass fraction X[1] = -0.00327104 of substance water
|                 | |       | of medium "Buildings.Media.Air" is not in the range 0..1"
LOG_ASSERT        | info    | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Fluid/Movers/FlowControlled_m_flow.mo:87:3-92:58:writable]
|                 | |       | The following assertion has been violated at time 15552069.120000
|                 | |       | (((-fan.dp) <= fan.dpMax), fan.dp=-146535.9555479615, fan.dpMax=2000) --> "In System3.fan: Model operates with head -dp = 146536 Pa,
|                 | |       |     exceeding the pressure allowed by the parameter System3.fan.dpMax.
|                 | |       |     This can happen if the model forces a high mass flow rate through a closed actuator,
|                 | |       |     or if the performance record is unreasonable. Please verify your model, and
|                 | |       |     consider using one of the other pump or fan models."
Traceback (most recent call last):
  File "<frozen runpy>", line 198, in _run_module_as_main
  File "<frozen runpy>", line 88, in _run_code
  File "/home/hudson/saved_omc/OMSimulator/install/lib/x86_64-linux-gnu/OMSimulator/__main__.py", line 38, in <module>
    sys.exit(main())
             ~~~~^^
  File "/home/hudson/saved_omc/OMSimulator/install/lib/x86_64-linux-gnu/OMSimulator/cli.py", line 309, in main
    handler(args.model, args)
    ~~~~~~~^^^^^^^^^^^^^^^^^^
  File "/home/hudson/saved_omc/OMSimulator/install/lib/x86_64-linux-gnu/OMSimulator/cli.py", line 176, in _runFMU
    fmu.simulate()
    ~~~~~~~~~~~~^^
  File "/home/hudson/saved_omc/OMSimulator/install/lib/x86_64-linux-gnu/OMSimulator/fmu.py", line 906, in simulate
    raise RuntimeError(f"Failed to simulate model: {status}")
RuntimeError: Failed to simulate model: Status.error
info:    0 warnings
info:    3 errors