startTime=0
stopTime=15
tolerance=1e-06
numberOfIntervals=2500
stepSize=0.006
Regular simulation: ./IDEAS_dev_IDEAS.Fluid.Actuators.Valves.Simplified.Examples.Thermostatic3WayValve  -abortSlowSimulation -alarm=480 -lv LOG_STATS
stdout            | info    | 
|                 | |       | Warning:
|                 | |       | ========
|                 | |       | It is recommended that the volume flow rate versus pressure relation
|                 | |       | of the fan or pump satisfies the minimum decrease condition
|                 | |       | 
|                 | |       |         (per.pressure.dp[i+1]-per.pressure.dp[i])
|                 | |       | d[i] = ------------------------------------------------- < -0
|                 | |       |        (per.pressure.V_flow[i+1]-per.pressure.V_flow[i])
|                 | |       | 
|                 | |       |  is
|                 | |       |   d[1]=0     
|                 | |       | 
|                 | |       | Otherwise, a solution to the equations may not exist if the fan or pump speed is reduced.
|                 | |       | In this situation, the solver will fail due to non-convergence and
|                 | |       | the simulation stops.
assert            | warning | The following assertion has been violated during initialization at time 0.000000
|                 | |       | pump.nominalValuesDefineDefaultPressureCurve
assert            | warning | *** Warning: You are using a flow or pressure controlled mover with the
|                 | |       |              default pressure curve.
|                 | |       |              This leads to approximate calculations of the electrical power
|                 | |       |              consumption. Add the correct pressure curve in the record per
|                 | |       |              to obtain an accurate computation.
|                 | |       |              Setting nominalValuesDefineDefaultPressureCurve=true will suppress this warning.
LOG_SUCCESS       | info    | The initialization finished successfully without homotopy method.
LOG_STATS         | info    | ### STATISTICS ###
|                 | |       | | timer
|                 | |       | | |   0.00585047s          reading init.xml
|                 | |       | | |   0.00067183s          reading info.xml
|                 | |       | | |   7.6524e-05s [  0.6%] pre-initialization
|                 | |       | | |  0.000162264s [  1.2%] initialization
|                 | |       | | |    1.323e-06s [  0.0%] steps
|                 | |       | | |  0.000698189s [  5.1%] solver (excl. callbacks)
|                 | |       | | |            0s [  0.0%] creating output-file
|                 | |       | | |  0.000248313s [  1.8%] event-handling
|                 | |       | | |   0.00453532s [ 32.9%] overhead
|                 | |       | | |   0.00806163s [ 58.5%] simulation
|                 | |       | | |    0.0137836s [100.0%] total
|                 | |       | | events
|                 | |       | | |     1 state events
|                 | |       | | |     0 time events
|                 | |       | | solver: dassl
|                 | |       | | |   160 steps taken
|                 | |       | | |   264 calls of functionODE
|                 | |       | | |    72 evaluations of jacobian
|                 | |       | | |    21 error test failures
|                 | |       | | |     0 convergence test failures
|                 | |       | | | 6.4401e-05s time of jacobian evaluation
LOG_SUCCESS       | info    | The simulation finished successfully.