Environment - simulationEnvironment:
startTime=0
stopTime=1
tolerance=1e-06
numberOfIntervals=2500
stepSize=0.0004
Regular simulation: ./Buildings_latest_Buildings.Fluid.FMI.Validation.HeaterFan  -abortSlowSimulation -alarm=480 -s gbode -emit_protected -lv LOG_STATS
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 11.0.0-master/Fluid/Movers/BaseClasses/PartialFlowMachine.mo:389:3-396:39:writable]
|                 | |       | The following assertion has been violated during initialization at time 0.000000
|                 | |       | ((false)) --> "*** Warning in HeaterFan.floMac.com: Mover is flow or pressure controlled and uses default pressure curve.
|                 | |       | This leads to an approximate power consumption.
|                 | |       | Set nominalValuesDefineDefaultPressureCurve=true to suppress this warning."
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 11.0.0-master/Fluid/Movers/BaseClasses/PartialFlowMachine.mo:417:3-427:39:writable]
|                 | |       | The following assertion has been violated during initialization at time 0.000000
|                 | |       | ((false)) --> "*** Warning in HeaterFan.floMac.com: Mover has per.etaHydMet=.Power_VolumeFlowRate or per.etaHydMet=.EulerNumber.
|                 | |       | This requires per.pressure to be provided.
|                 | |       | Because it is not, the model overrides this setting by using per.etaHydMet=.NotProvided.
|                 | |       | Also consider using models under Movers.Preconfigured which autopopulate a pressure curve."
LOG_ASSERT        | warning | [/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 11.0.0-master/Fluid/Movers/BaseClasses/PartialFlowMachine.mo:429:3-439:39:writable]
|                 | |       | The following assertion has been violated during initialization at time 0.000000
|                 | |       | ((false)) --> "*** Warning in HeaterFan.floMac.com: Mover has per.etaMotMet=.Efficiency_MotorPartLoadRatio or per.etaMotMet=.GenericCurve.
|                 | |       | This requires per.WMot_nominal or per.pressure to be provided. Because neither is provided,
|                 | |       | the model overrides this setting and by using per.etaMotMet=.NotProvided.
|                 | |       | Also consider using models under Movers.Preconfigured which autopopulate a pressure curve."
LOG_SUCCESS       | info    | The initialization finished successfully without homotopy method.
LOG_STATS         | info    | ### STATISTICS ###
|                 | |       | | timer
|                 | |       | | |   0.00921765s          reading init.xml
|                 | |       | | |    0.0010233s          reading info.xml
|                 | |       | | |  0.000532309s [  4.9%] pre-initialization
|                 | |       | | |  0.000296696s [  2.7%] initialization
|                 | |       | | |     9.02e-07s [  0.0%] steps
|                 | |       | | |    9.833e-06s [  0.1%] solver (excl. callbacks)
|                 | |       | | |   0.00110191s [ 10.1%] creating output-file
|                 | |       | | | -6.85567e-21s [ -0.0%] event-handling
|                 | |       | | |   0.00340749s [ 31.2%] overhead
|                 | |       | | |    0.0055349s [ 50.7%] simulation
|                 | |       | | |    0.0109575s [100.0%] total
|                 | |       | | events
|                 | |       | | |     0 state events
|                 | |       | | |     0 time events
|                 | |       | | solver: euler
|                 | |       | | |  5000 steps taken
|                 | |       | | |  5000 calls of functionODE
|                 | |       | | |     0 evaluations of jacobian
|                 | |       | | |     0 error test failures
|                 | |       | | |     0 convergence test failures
|                 | |       | | | 0s time of jacobian evaluation
LOG_SUCCESS       | info    | The simulation finished successfully.