Environment - simulationEnvironment:
startTime=0
stopTime=1
tolerance=1e-06
numberOfIntervals=2500
stepSize=0.0004
Regular simulation: ./Buildings_10_Buildings.Fluid.FMI.Validation.HeaterFanPressureDriven  -abortSlowSimulation -alarm=480  -emit_protected -lv LOG_STATS
assert            | warning | The following assertion has been violated during initialization at time 0.000000
|                 | |       | false
assert            | warning | *** Warning in HeaterFanPressureDriven.floMac.com: Mover is flow or pressure controlled and uses default pressure curve.
|                 | |       | This leads to an approximate power consumption.
|                 | |       | Set nominalValuesDefineDefaultPressureCurve=true to suppress this warning.
assert            | warning | The following assertion has been violated during initialization at time 0.000000
|                 | |       | false
assert            | warning | *** Warning in HeaterFanPressureDriven.floMac.com: Mover has per.etaHydMet=.Power_VolumeFlowRate or per.etaHydMet=.EulerNumber.
|                 | |       | This requires per.pressure to be provided.
|                 | |       | Because it is not, the model overrides this setting by using per.etaHydMet=.NotProvided.
|                 | |       | Also consider using models under Movers.Preconfigured which autopopulate a pressure curve.
assert            | warning | The following assertion has been violated during initialization at time 0.000000
|                 | |       | false
assert            | warning | *** Warning in HeaterFanPressureDriven.floMac.com: Mover has per.etaMotMet=.Efficiency_MotorPartLoadRatio or per.etaMotMet=.GenericCurve.
|                 | |       | This requires per.WMot_nominal or per.pressure to be provided. Because neither is provided,
|                 | |       | the model overrides this setting and by using per.etaMotMet=.NotProvided.
|                 | |       | Also consider using models under Movers.Preconfigured which autopopulate a pressure curve.
LOG_SUCCESS       | info    | The initialization finished successfully with 3 homotopy steps.
LOG_STATS         | info    | ### STATISTICS ###
|                 | |       | | timer
|                 | |       | | |    0.0103328s          reading init.xml
|                 | |       | | |  0.000878298s          reading info.xml
|                 | |       | | |  0.000776656s [  5.6%] pre-initialization
|                 | |       | | |  0.000386164s [  2.8%] initialization
|                 | |       | | |    1.293e-06s [  0.0%] steps
|                 | |       | | |    7.007e-06s [  0.1%] solver (excl. callbacks)
|                 | |       | | |   0.00123878s [  8.9%] creating output-file
|                 | |       | | | -7.27919e-21s [ -0.0%] event-handling
|                 | |       | | |   0.00373189s [ 26.7%] overhead
|                 | |       | | |   0.00778453s [ 55.7%] simulation
|                 | |       | | |    0.0140066s [100.0%] total
|                 | |       | | events
|                 | |       | | |     0 state events
|                 | |       | | |     0 time events
|                 | |       | | solver: euler
|                 | |       | | |  5000 steps taken
|                 | |       | | |  5000 calls of functionODE
|                 | |       | | |     0 evaluations of jacobian
|                 | |       | | |     0 error test failures
|                 | |       | | |     0 convergence test failures
|                 | |       | | | 0s time of jacobian evaluation
LOG_SUCCESS       | info    | The simulation finished successfully.