startTime=0
stopTime=3600
tolerance=1e-06
numberOfIntervals=3600
stepSize=1
wasm-jit simulation: simulate(Modelica.Fluid.Examples.AST_BatchPlant.BatchPlant_StandardWater,startTime=0,stopTime=3600,tolerance=1e-06,numberOfIntervals=3600,outputFormat="mat",variableFilter="time|B5.medium.h|B5.level|B5.InnerTankTop.[0-9,]+..m_flow_negative|B5.InnerTankSide.[0-9,]+..m_flow_negative|B5.InnerTankBottom.[0-9,]+..m_flow_negative|controller.Transition1.enableFire|controller.Transition2.enableFire|controller.Transition3.enableFire|controller.Transition4.enableFire|controller.Transition5.enableFire|controller.Transition6.enableFire|controller.Transition7.enableFire|controller.Transition8.enableFire|controller.Transition9.enableFire|controller.Transition10.enableFire|controller.Transition11.enableFire|controller.Transition12.enableFire|controller.Transition13.enableFire|controller.TransitionWithSignal1.enableFire|volume5.medium.p|volume5.medium.h|P1.medium.p|P1.medium.h|P2.medium.p|P2.medium.h|B1.level|B1.medium.h|P1_on.y|P2_on.y|B2.level|B2.medium.h|B3.level|B3.medium.h|B4.level|B4.medium.h|B7.level|B7.medium.h|pipeB1B2.mediums.[0-9,]+..p|pipeB1B2.mediums.[0-9,]+..h|pipePump1B1.mediums.[0-9,]+..p|pipePump1B1.mediums.[0-9,]+..h|pipePump2B2.mediums.[0-9,]+..p|pipePump2B2.mediums.[0-9,]+..h|B6.level|B6.medium.h|volume4.medium.p|volume4.medium.h",fileNamePrefix="Modelica_trunk_Modelica.Fluid.Examples.AST_BatchPlant.BatchPlant_StandardWater",simflags="-abortSlowSimulation -alarm=240  -emit_protected -lv LOG_STATS")
Simulation execution failed for model: Modelica.Fluid.Examples.AST_BatchPlant.BatchPlant_StandardWater
LOG_STDOUT        | warning | Sparsity pattern for non-linear system 0 is not regular. This indicates that something went wrong during sparsity pattern generation. Removing sparsity pattern and disabling NLS scaling.
LOG_STDOUT        | warning | The default linear solver fails, the fallback solver with total pivoting is started at time 0.000000. That might raise performance issues, for more information use -lv LOG_LS.
LOG_STDOUT        | warning | The default linear solver fails, the fallback solver with total pivoting is started at time 0.000000. That might raise performance issues, for more information use -lv LOG_LS.
LOG_ASSERT        | warning | Homotopy algorithm did not converge.
|                 | |       | The maximum number of lambda steps is reached (3700).
|                 | |       | You can change the maximum number of lambda steps with:
|                 | |       |   -homMaxLambdaSteps=<value>
|                 | |       | You can also try to influence the step size tau with the following flags:
|                 | |       |   -homTauDecFac=<value>
|                 | |       |   -homTauDecFacPredictor=<value>
|                 | |       |   -homTauIncFac=<value>
|                 | |       |   -homTauIncThreshold=<value>
|                 | |       |   -homTauMax=<value>
|                 | |       |   -homTauMin=<value>
|                 | |       |   -homTauStart=<value>
|                 | |       | or you can also set the threshold for accepting the current bending with:
|                 | |       |   -homAdaptBend=<value>
|                 | |       | You can also try to use another backtrace stategy in the corrector step with:
|                 | |       |   -homBacktraceStrategy=<fix|orthogonal>
|                 | |       | You can use -lv=LOG_INIT_HOMOTOPY,LOG_NLS_HOMOTOPY to get more information.
LOG_ASSERT        | info    | The homotopy algorithm is started again with opposing start direction.
LOG_ASSERT        | warning | Homotopy algorithm did not converge.
|                 | |       | lambda is smaller than -1: lambda=-1.05622
|                 | |       | You can use -lv=LOG_INIT_HOMOTOPY,LOG_NLS_HOMOTOPY to get more information.
LOG_ASSERT        | debug   | Solving non-linear system 1207 failed at time=0.
|                 | |       | For more information please use -lv LOG_NLS.
LOG_ASSERT        | info    | simulation terminated by an assertion at initialization