startTime=0
stopTime=10
tolerance=1e-06
numberOfIntervals=5003
stepSize=0.0019988
wasm-jit simulation: simulate(ModelicaTest.Fluid.TestComponents.Machines.TestWaterPumpVariableSpeed,startTime=0,stopTime=10,tolerance=1e-06,numberOfIntervals=5003,outputFormat="mat",variableFilter="time|N_pump.y|Source.ports.[0-9,]+..m_flow|Source.ports.[0-9,]+..p|Source.ports.[0-9,]+..h_outflow|Sink.ports.[0-9,]+..m_flow|Sink.ports.[0-9,]+..p|Sink.ports.[0-9,]+..h_outflow|pump.port_b.m_flow|pump.port_b.p|pump.port_b.h_outflow|valveOpening.y|Valve.port_b.m_flow|Valve.port_b.p|Valve.port_b.h_outflow|Valve.minLimiter.y",fileNamePrefix="ModelicaTest_4.1.0_ModelicaTest.Fluid.TestComponents.Machines.TestWaterPumpVariableSpeed",simflags="-abortSlowSimulation -alarm=240  -emit_protected -lv LOG_STATS")
Simulation execution failed for model: ModelicaTest.Fluid.TestComponents.Machines.TestWaterPumpVariableSpeed
LOG_STDOUT        | warning | Sparsity pattern for non-linear system 0 is not regular. This indicates that something went wrong during sparsity pattern generation. Removing sparsity pattern and disabling NLS scaling.
LOG_ASSERT        | warning | Homotopy algorithm did not converge.
|                 | |       | The step size tau cannot be decreased anymore and current tau=9.76563e-05 already failed.
|                 | |       | You can influence the calculation of tau with the following flags:
|                 | |       |   -homTauDecFac=<value>
|                 | |       |   -homTauDecFacPredictor=<value>
|                 | |       |   -homTauIncFac=<value>
|                 | |       |   -homTauIncThreshold=<value>
|                 | |       |   -homTauMax=<value>
|                 | |       |   -homTauMin=<value>
|                 | |       |   -homTauStart=<value>
|                 | |       | You can also set the threshold for accepting the current bending with:
|                 | |       |   -homAdaptBend=<value>
|                 | |       | You can use -lv=LOG_INIT_HOMOTOPY,LOG_NLS_HOMOTOPY to get more information.
LOG_ASSERT        | info    | The homotopy algorithm is started again with opposing start direction.
LOG_ASSERT        | warning | Homotopy algorithm did not converge.
|                 | |       | The step size tau cannot be decreased anymore and current tau=7.62939e-05 already failed.
|                 | |       | You can influence the calculation of tau with the following flags:
|                 | |       |   -homTauDecFac=<value>
|                 | |       |   -homTauDecFacPredictor=<value>
|                 | |       |   -homTauIncFac=<value>
|                 | |       |   -homTauIncThreshold=<value>
|                 | |       |   -homTauMax=<value>
|                 | |       |   -homTauMin=<value>
|                 | |       |   -homTauStart=<value>
|                 | |       | You can also set the threshold for accepting the current bending with:
|                 | |       |   -homAdaptBend=<value>
|                 | |       | You can use -lv=LOG_INIT_HOMOTOPY,LOG_NLS_HOMOTOPY to get more information.
LOG_ASSERT        | debug   | Solving non-linear system 60 failed at time=0.
|                 | |       | For more information please use -lv LOG_NLS.
LOG_ASSERT        | info    | simulation terminated by an assertion at initialization