startTime=0
stopTime=864000
tolerance=1e-06
numberOfIntervals=2500
stepSize=345.6
wasm-jit simulation: simulate(Buildings.ThermalZones.Detailed.FLEXLAB.Rooms.Examples.X3WithRadiantFloor,startTime=0,stopTime=864000,tolerance=1e-06,numberOfIntervals=2500,outputFormat="mat",variableFilter="time|X3B.air.vol.T|BClo.air.vol.T|BEle.air.vol.T|X3A.air.vol.T|AClo.air.vol.T|AEle.air.vol.T|X3A.surf_surBou.[0-9,]+..T|X3B.surf_surBou.[0-9,]+..T",fileNamePrefix="Buildings_12_Buildings.ThermalZones.Detailed.FLEXLAB.Rooms.Examples.X3WithRadiantFloor",simflags="-abortSlowSimulation -alarm=240  -emit_protected -lv LOG_STATS")
Simulation execution failed for model: Buildings.ThermalZones.Detailed.FLEXLAB.Rooms.Examples.X3WithRadiantFloor
LOG_STDOUT        | warning | Sparsity pattern for non-linear system 0 is not regular. This indicates that something went wrong during sparsity pattern generation. Removing sparsity pattern and disabling NLS scaling.
LOG_STDOUT        | info    | ... loading "airCon" from "/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Resources/Data/ThermalZones/Detailed/FLEXLAB/Rooms/Examples/X3AWithRadiantFloor.txt"
LOG_STDOUT        | info    | ... loading "airCon" from "/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Resources/Data/ThermalZones/Detailed/FLEXLAB/Rooms/Examples/X3AWithRadiantFloor.txt"
LOG_STDOUT        | info    | ... loading "airCon" from "/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Resources/Data/ThermalZones/Detailed/FLEXLAB/Rooms/Examples/X3AWithRadiantFloor.txt"
LOG_STDOUT        | info    | ... loading "airCon" from "/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Resources/Data/ThermalZones/Detailed/FLEXLAB/Rooms/Examples/X3AWithRadiantFloor.txt"
LOG_STDOUT        | info    | ... loading "airCon" from "/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Resources/Data/ThermalZones/Detailed/FLEXLAB/Rooms/Examples/X3AWithRadiantFloor.txt"
LOG_STDOUT        | info    | ... loading "airCon" from "/home/hudson/saved_omc/libraries/.openmodelica/libraries/Buildings 12.1.3-maint.12.x/Resources/Data/ThermalZones/Detailed/FLEXLAB/Rooms/Examples/X3AWithRadiantFloor.txt"
LOG_STDOUT        | warning | The default linear solver fails, the fallback solver with total pivoting is started at time 0.000000. That might raise performance issues, for more information use -lv LOG_LS.
LOG_STDOUT        | warning | The default linear solver fails, the fallback solver with total pivoting is started at time 0.000000. That might raise performance issues, for more information use -lv LOG_LS.
LOG_ASSERT        | warning | Homotopy algorithm did not converge.
|                 | |       | No solution for current step size tau found and tau cannot be decreased any further.
|                 | |       | You can set the minimum step size tau with:
|                 | |       |   -homTauMin=<value>
|                 | |       | You can also try to allow more newton steps in the corrector step with:
|                 | |       |   -homMaxNewtonSteps=<value>
|                 | |       | or change the tolerance for the solution with:
|                 | |       |   -homHEps=<value>
|                 | |       | You can also try to use another backtrace stategy in the corrector step with:
|                 | |       |   -homBacktraceStrategy=<fix|orthogonal>
|                 | |       | You can use -lv=LOG_INIT_HOMOTOPY,LOG_NLS_HOMOTOPY to get more information.
LOG_ASSERT        | info    | The homotopy algorithm is started again with opposing start direction.
LOG_ASSERT        | warning | Homotopy algorithm did not converge.
|                 | |       | No solution for current step size tau found and tau cannot be decreased any further.
|                 | |       | You can set the minimum step size tau with:
|                 | |       |   -homTauMin=<value>
|                 | |       | You can also try to allow more newton steps in the corrector step with:
|                 | |       |   -homMaxNewtonSteps=<value>
|                 | |       | or change the tolerance for the solution with:
|                 | |       |   -homHEps=<value>
|                 | |       | You can also try to use another backtrace stategy in the corrector step with:
|                 | |       |   -homBacktraceStrategy=<fix|orthogonal>
|                 | |       | You can use -lv=LOG_INIT_HOMOTOPY,LOG_NLS_HOMOTOPY to get more information.
LOG_ASSERT        | debug   | Solving non-linear system 7059 failed at time=0.
|                 | |       | For more information please use -lv LOG_NLS.
LOG_ASSERT        | info    | simulation terminated by an assertion at initialization