startTime=0
stopTime=200
tolerance=1e-06
numberOfIntervals=2500
stepSize=0.08
wasm-jit simulation: simulate(Buildings.Templates.Components.Validation.Coils,startTime=0,stopTime=200,tolerance=1e-06,numberOfIntervals=2500,outputFormat="mat",variableFilter="time|coiCoo.bus.y|coiCoo.bus.y_actual|coiCoo.hex.m1_flow|coiCoo.hex.m2_flow|coiCoo.hex.m1_flow_nominal|coiCoo.hex.m2_flow_nominal|coiCoo.hex.Q2_flow|coiCoo.Q_flow_nominal|coiHea.bus.y|coiHea.bus.y_actual|coiHea.hex.m1_flow|coiHea.hex.m2_flow|coiHea.hex.m1_flow_nominal|coiHea.hex.m2_flow_nominal|coiHea.hex.Q2_flow|coiHea.Q_flow_nominal|coiEle.bus.y|coiEle.hex.m_flow|coiEle.hex.m_flow_nominal|coiEle.hex.Q_flow|coiEle.Q_flow_nominal|coiEva.bus.y|coiEva.hex.m_flow|coiEva.hex.m_flow_nominal|coiEva.hex.QSen_flow|coiEva.hex.QLat_flow|coiEva.Q_flow_nominal|coiMul.bus.y|coiMul.hex.m_flow|coiMul.hex.m_flow_nominal|coiMul.hex.QSen_flow|coiMul.hex.QLat_flow|coiMul.Q_flow_nominal|non.m_flow|non.m_flow_nominal",fileNamePrefix="Buildings_11_Buildings.Templates.Components.Validation.Coils",simflags="-abortSlowSimulation -alarm=240  -emit_protected -lv LOG_STATS")
Simulation execution failed for model: Buildings.Templates.Components.Validation.Coils
LOG_STDOUT        | warning | Sparsity pattern for non-linear system 0 is not regular. This indicates that something went wrong during sparsity pattern generation. Removing sparsity pattern and disabling NLS scaling.
LOG_STDOUT        | warning | Sparsity pattern for non-linear system 1 is not regular. This indicates that something went wrong during sparsity pattern generation. Removing sparsity pattern and disabling NLS scaling.
LOG_ASSERT        | warning | Homotopy algorithm did not converge.
|                 | |       | lambda is smaller than -1: lambda=-1.25773
|                 | |       | You can use -lv=LOG_INIT_HOMOTOPY,LOG_NLS_HOMOTOPY to get more information.
LOG_ASSERT        | info    | The homotopy algorithm is started again with opposing start direction.
LOG_ASSERT        | warning | Homotopy algorithm did not converge.
|                 | |       | The maximum number of lambda steps is reached (3700).
|                 | |       | You can change the maximum number of lambda steps with:
|                 | |       |   -homMaxLambdaSteps=<value>
|                 | |       | You can also try to influence the step size tau with the following flags:
|                 | |       |   -homTauDecFac=<value>
|                 | |       |   -homTauDecFacPredictor=<value>
|                 | |       |   -homTauIncFac=<value>
|                 | |       |   -homTauIncThreshold=<value>
|                 | |       |   -homTauMax=<value>
|                 | |       |   -homTauMin=<value>
|                 | |       |   -homTauStart=<value>
|                 | |       | or you can also set the threshold for accepting the current bending with:
|                 | |       |   -homAdaptBend=<value>
|                 | |       | You can also try to use another backtrace stategy in the corrector step with:
|                 | |       |   -homBacktraceStrategy=<fix|orthogonal>
|                 | |       | You can use -lv=LOG_INIT_HOMOTOPY,LOG_NLS_HOMOTOPY to get more information.
LOG_ASSERT        | debug   | Solving non-linear system 494 failed at time=0.
|                 | |       | For more information please use -lv LOG_NLS.
LOG_ASSERT        | info    | simulation terminated by an assertion at initialization