startTime=0
stopTime=172800
tolerance=1e-06
numberOfIntervals=2500
stepSize=69.12
wasm-jit simulation: simulate(Buildings.Examples.DualFanDualDuct.ClosedLoop,startTime=0,stopTime=172800,tolerance=1e-06,numberOfIntervals=2500,outputFormat="mat",variableFilter="time|fanSupHot.m_flow|fanSupCol.m_flow|fanRet.m_flow|fanSupHot.dp|fanSupCol.dp|fanRet.dp|flo.sou.air.vol.T|flo.eas.air.vol.T|flo.nor.air.vol.T|flo.wes.air.vol.T|flo.cor.air.vol.T|cor.vavHot.m_flow|sou.vavHot.m_flow|eas.vavHot.m_flow|nor.vavHot.m_flow|wes.vavHot.m_flow|cor.vavCol.m_flow|sou.vavCol.m_flow|eas.vavCol.m_flow|nor.vavCol.m_flow|wes.vavCol.m_flow|weaDat.weaBus.TDryBul|weaDat.weaBus.HGloHor|weaDat.weaBus.HDifHor|conEco.VOut_flow_min|conEco.VOut_flow|conEco.yOA|conEco.yOATFre.y|conEco.conV_flow.y|conEco.uOATSup",fileNamePrefix="Buildings_11_Buildings.Examples.DualFanDualDuct.ClosedLoop",simflags="-abortSlowSimulation -alarm=360  -emit_protected -lv LOG_STATS")
Simulation execution failed for model: Buildings.Examples.DualFanDualDuct.ClosedLoop
LOG_STDOUT        | warning | Sparsity pattern for non-linear system 0 is not regular. This indicates that something went wrong during sparsity pattern generation. Removing sparsity pattern and disabling NLS scaling.
LOG_ASSERT        | warning | Homotopy algorithm did not converge.
|                 | |       | No solution for current step size tau found and tau cannot be decreased any further.
|                 | |       | You can set the minimum step size tau with:
|                 | |       |   -homTauMin=<value>
|                 | |       | You can also try to allow more newton steps in the corrector step with:
|                 | |       |   -homMaxNewtonSteps=<value>
|                 | |       | or change the tolerance for the solution with:
|                 | |       |   -homHEps=<value>
|                 | |       | You can also try to use another backtrace stategy in the corrector step with:
|                 | |       |   -homBacktraceStrategy=<fix|orthogonal>
|                 | |       | You can use -lv=LOG_INIT_HOMOTOPY,LOG_NLS_HOMOTOPY to get more information.
LOG_ASSERT        | info    | The homotopy algorithm is started again with opposing start direction.
LOG_ASSERT        | warning | Homotopy algorithm did not converge.
|                 | |       | No solution for current step size tau found and tau cannot be decreased any further.
|                 | |       | You can set the minimum step size tau with:
|                 | |       |   -homTauMin=<value>
|                 | |       | You can also try to allow more newton steps in the corrector step with:
|                 | |       |   -homMaxNewtonSteps=<value>
|                 | |       | or change the tolerance for the solution with:
|                 | |       |   -homHEps=<value>
|                 | |       | You can also try to use another backtrace stategy in the corrector step with:
|                 | |       |   -homBacktraceStrategy=<fix|orthogonal>
|                 | |       | You can use -lv=LOG_INIT_HOMOTOPY,LOG_NLS_HOMOTOPY to get more information.
LOG_ASSERT        | debug   | Solving non-linear system 5454 failed at time=0.
|                 | |       | For more information please use -lv LOG_NLS.
LOG_ASSERT        | info    | simulation terminated by an assertion at initialization